Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2018.10–2019.09
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

DCM (telematics transceiver)*

·

Harness or connector



*: w/ Telematics Transceiver and for 6 Speakers


WIRING DIAGRAM

E402555E08
0.698,2.344 2.083,2.719 1.385,0.375 10 false Telephone Microphone Assembly 0.635,3.073 1.24,3.26 0.604,0.188 10 false P14 2.854,2.563 5.177,2.802 2.323,0.24 10 false DCM (Telematics Transceiver) 2.844,2.385 3.177,2.563 0.333,0.177 10 false H6 5.594,2.646 6.844,3.188 1.25,0.542 10 false Radio and Display Receiver Assembly 5.594,2.469 5.938,2.646 0.344,0.177 10 false G2 5.76,0.927 6.198,1.094 0.438,0.167 10 false SNS2 5.5,0.792 5.75,0.958 0.25,0.167 10 false 25 3.24,1.875 3.677,2.042 0.438,0.167 10 false MCI- 2.979,1.76 3.208,1.938 0.229,0.177 10 false 35 1.333,0.938 1.771,1.104 0.438,0.167 10 false SNS2 1.792,0.802 1.958,0.979 0.167,0.177 10 false 1 1.375,1.865 1.813,2.031 0.438,0.167 10 false MIC- 1.813,1.771 1.979,1.948 0.167,0.177 10 false 2 0.146,0.063 4.083,0.313 3.938,0.25 12 false w/ Telematics Transceiver and for 6 Speakers: 0.646,3.229 2.969,3.469 2.323,0.24 10 false Map Light Assembly 2.104,0.792 2.542,0.958 0.438,0.167 10 false SNS2 2.594,0.802 2.76,0.979 0.167,0.177 10 false 4 2.125,1.771 2.563,1.938 0.438,0.167 10 false MCO- 2.604,1.76 2.771,1.938 0.167,0.177 10 false 5 0.719,2.125 0.969,2.313 0.25,0.188 10 false A


E402556E08
0.115,0.083 4.26,0.323 4.146,0.24 12 false w/o Telematics Transceiver or for 9 Speakers: 1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false G2 5.74,2.635 7.031,3.083 1.292,0.448 10 false Radio and Display Receiver Assembly 0.917,3.073 1.375,3.302 0.458,0.229 10 false P14 1.052,2.365 2.479,2.854 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.104,0.833 3.563,1.063 0.458,0.229 10 false 4 3.115,1.844 3.573,2.073 0.458,0.229 10 false 5 1.073,2.115 1.531,2.344 0.458,0.229 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver and for 6 Speakers A
w/o Telematics Transceiver or w/ Telematics Transceiver and for 9 Speakers B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the P14 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P14-4 (SNS2) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)
a.

Disconnect the H6 DCM (telematics transceiver) connector.


b.

Disconnect the P14 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-35 (MCI-) - P14-5 (MCO-) Always Below 1 Ω
H6-35 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)
a.
E364292C17
1.583,0.479 1.99,0.76 0.406,0.281 0.833,2.813 1.021,2.813 1.021,2.813 1.229,2.063 true 1.688,0.531 1.979,0.698 0.292,0.167 10 false H6 0.448,2.75 0.906,2.948 0.458,0.198 10 false MCI- 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the P14 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P14-4 (SNS2) Always Below 1 Ω
G2-22 (MIN-) - P14-5 (MCO-) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher
G2-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360500C18
1.781,1.229 1.333,0.698 false 1.938,1.219 2.417,0.719 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.115,0.521 1.625,0.729 0.51,0.208 10 false MCO- 2.344,0.542 2.875,0.802 0.531,0.26 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SNS2) - 5 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

7.INSPECT MAP LIGHT ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.
E369493C69
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 1.74,1.438 1.24,0.927 true 1.896,1.438 2.323,0.927 true 1.396,3.479 1.156,3.885 true 1.844,3.917 1.542,3.469 true 0.125,0.208 0.438,0.406 0.313,0.198 10 false *a 2.25,0.75 2.75,0.969 0.5,0.219 10 false SNS2 1,0.75 1.479,0.958 0.479,0.208 10 false MCO- 1.635,2.854 1.948,3.052 0.313,0.198 10 false A 1.542,0.438 2.021,0.646 0.479,0.208 10 false P14 0.708,3.865 1.208,4.083 0.5,0.219 10 false SNS2 1.896,3.875 2.375,4.083 0.479,0.208 10 false MIC-
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-4 (SNS2) - A-1 (SNS2) Always Below 1 Ω
P14-5 (MCO-) - A-2 (MIC-) Always Below 1 Ω
P14-4 (SNS2) - Body ground Always 10 kΩ or higher
P14-5 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY