Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3620E _58 Vehicle Interior _076051 METER / GAUGE / DISPLAY _0374621 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter assembly receives signals from this circuit to adjust the illumination of the combination meter assembly. The combination meter assembly sets the illumination level based on the user operation of the light control rheostat switch.

WIRING DIAGRAM

E407650E01
1.365,1.406 4.115,1.604 2.75,0.198 10 false Tail Cancel Switch 4.844,3.125 6.74,3.385 1.896,0.26 10 false G18 4.854,3.302 6.75,3.563 1.896,0.26 10 false Combination Meter Assembly 1.104,3.156 3,3.417 1.896,0.26 10 false G108 1.104,3.302 3,3.563 1.896,0.26 10 false Light Control Rheostat 2.375,0.552 4.271,0.813 1.896,0.26 10 false T 2.302,1.115 4.198,1.375 1.896,0.26 10 false TC 2.604,1.115 4.5,1.375 1.896,0.26 10 false 3 2.604,0.573 4.5,0.833 1.896,0.26 10 false 5 2.635,1.74 4.51,1.979 1.875,0.24 10 false 4 2.625,2.365 4.5,2.604 1.875,0.24 10 false 2 2.302,1.771 4.198,2.031 1.896,0.26 10 false TR 5.125,1.74 5.677,2.125 0.552,0.385 10 false SW2 5.135,2.375 5.688,2.76 0.552,0.385 10 false SW3 5.125,0.542 5.677,0.927 0.552,0.385 10 false SW1 5.125,1.115 5.677,1.5 0.552,0.385 10 false TC 4.823,1.094 5.375,1.479 0.552,0.385 10 false 17 4.802,0.542 5.354,0.927 0.552,0.385 10 false 34 4.802,1.74 5.354,2.125 0.552,0.385 10 false 16 4.802,2.365 5.354,2.75 0.552,0.385 10 false 11 2.365,2.365 4.24,2.604 1.875,0.24 10 false E 5.854,0.406 6.208,0.75 0.354,0.344 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:
·

The meter illumination level can be adjusted by pressing the light control rheostat switch.

·

The meter illumination dims when the taillights are turned on.

·

Setting the meter illumination level to maximum brightness cancels the above dimming of the meter illumination.



PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Meter Day Mode Switch Light control rheostat (tail cancel switch) signal OFF or ON OFF: Light control rheostat (tail cancel switch) off
ON: Light control rheostat (tail cancel switch) on
-
Rheostat value Light control rheostat input signal Min.: 0.00%, Max.: 100.02% or Unset Light control rheostat dark (0.00%) → bright (100.02%) -
Body Electrical > Combination Meter > Data List
Tester Display
Meter Day Mode Switch
Rheostat value
50003 409 5,22
OK:

Light control rheostat condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT LIGHT CONTROL RHEOSTAT
2.INSPECT LIGHT CONTROL RHEOSTAT
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - LIGHT CONTROL RHEOSTAT)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - LIGHT CONTROL RHEOSTAT)
a.

Disconnect the G18 combination meter assembly connector.


b.

Disconnect the G108 light control rheostat connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-34 (SW1) - G108-5 (T) Always Below 1 Ω
G18-17 (TC) - G108-3 (TC) Always Below 1 Ω
G18-16 (SW2) - G108-4 (TR) Always Below 1 Ω
G18-11 (SW3) - G108-2 (E) Always Below 1 Ω
G18-34 (SW1) or G108-5 (T) - Body ground Always 10 kΩ or higher
G18-17 (TC) or G108-3 (TC) - Body ground Always 10 kΩ or higher
G18-16 (SW2) or G108-4 (TR) - Body ground Always 10 kΩ or higher
G18-11 (SW3) or G108-2 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR