The combination meter assembly uses the fuel sender gauge assembly and No. 2 fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly and No. 2 fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly and operates the fuel receiver gauge.
The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and operates the fuel receiver gauge.
Be careful of flames.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Check if DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check if SFI system DTCs are output.
for A25A-FKS with Canister Pump Module:
for A25A-FKS without Canister Pump Module:
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for A25A-FXS with Canister Pump Module:
for A25A-FXS without Canister Pump Module:
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25A-FKS with Canister Pump Module:
for A25A-FKS without Canister Pump Module:
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for A25A-FXS with Canister Pump Module:
for A25A-FXS without Canister Pump Module:
Using the GTS, perform the Active Test.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Fuel Gauge Operation (Sender E) | Fuel receiver gauge (Sender E) | ON | See [Display] |
| Fuel Gauge Operation (Empty) | Fuel receiver gauge (Empty) | ON | See [Display] |
| Fuel Gauge Operation (Warning) | Fuel receiver gauge (Warning) | ON | See [Display] |
| Fuel Gauge Operation (1/4) | Fuel receiver gauge (1/4) | ON | See [Display] |
| Fuel Gauge Operation (1/2) | Fuel receiver gauge (1/2) | ON | See [Display] |
| Fuel Gauge Operation (3/4) | Fuel receiver gauge (3/4) | ON | See [Display] |
| Fuel Gauge Operation (Full) | Fuel receiver gauge (Full) | ON | See [Display] |
| Fuel Gauge Operation (Sender F) | Fuel receiver gauge (Sender F) | ON | See [Display] |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender E) |
| Tester Display |
|---|
| Fuel Gauge Operation (Empty) |
| Tester Display |
|---|
| Fuel Gauge Operation (Warning) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/2) |
| Tester Display |
|---|
| Fuel Gauge Operation (3/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (Full) |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender F) |
Fuel receiver gauge indication is normal.
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel receiver gauge
| Result | Proceed to |
|---|---|
| OK (for Gasoline Model) | A |
| OK (for HV Model) | B |
| NG | C |
A
B
C
Disconnect the G18 combination meter assembly connector.
Disconnect the N27 fuel suction with pump and gauge tube assembly connector.
Disconnect the M18 No. 2 fuel sender gauge assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-3 (FS) - G18-31 (FR) | Always | Below 1 Ω |
| N27-2 (FE) - G18-24 (FE&B) | Always | Below 1 Ω |
| N27-1 (FV) - G18-14 (FV) | Always | Below 1 Ω |
| M18-3 (FR) - G18-13 (FR2) | Always | Below 1 Ω |
| M18-2 (FE) - G18-24 (FE&B) | Always | Below 1 Ω |
| M18-1 (FV) - G18-14 (FV) | Always | Below 1 Ω |
| N27-3 (FS) or G18-31 (FR) - Other terminals and body ground | Always | 10 kΩ or higher |
| N27-2 (FE) or G18-24 (FE&B) - Other terminals and body ground | Always | 10 kΩ or higher |
| N27-1 (FV) or G18-14 (FV) - Other terminals and body ground | Always | 10 kΩ or higher |
| M18-3 (FR) or G18-13 (FR2) - Other terminals and body ground | Always | 10 kΩ or higher |
| M18-2 (FE) or G18-24 (FE&B) - Other terminals and body ground | Always | 10 kΩ or higher |
| M18-1 (FV) or G18-14 (FV) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
for A25A-FKS with Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
for A25-FKS without Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
for A25A-FKS with Canister Pump Module:
for A25-FKS without Canister Pump Module:
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25-FKS with Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
for A25-FKS without Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
| *a | Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-1 (FV) - A-3 | Always | Below 1 Ω |
| N27-2 (FE) - A-2 | Always | Below 1 Ω |
| N27-3 (FS) - A-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25-FKS with Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
for A25-FKS without Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Remove the No. 2 fuel sender gauge assembly.
for A25-FKS with Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
for A25-FKS without Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the No. 2 fuel sender gauge assembly.
for A25-FKS with Canister Pump Module:
for A25-FKS without Canister Pump Module:
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25-FKS with Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
for A25-FKS without Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Disconnect the N27 fuel suction with pump and gauge tube assembly connector.
Disconnect the G18 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-3 (FS) - G18-31 (FR) | Always | Below 1 Ω |
| N27-2 (FE) - G18-24 (FE&B) | Always | Below 1 Ω |
| N27-1 (FV) - G18-14 (FV) | Always | Below 1 Ω |
| N27-3 (FS) or G18-31 (FR) - Other terminals and body ground | Always | 10 kΩ or higher |
| N27-2 (FE) or G18-24 (FE&B) - Other terminals and body ground | Always | 10 kΩ or higher |
| N27-1 (FV) or G18-14 (FV) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
w/o Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
Inspect the fuel sender gauge assembly.
w/ Canister Pump Module:
w/o Canister Pump Module:
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
w/o Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
| *a | Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-1 (FV) - A-3 | Always | Below 1 Ω |
| N27-2 (FE) - A-2 | Always | Below 1 Ω |
| N27-3 (FS) - A-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module)>REMOVAL
w/o Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL