Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module) › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076683 A25A-FKS FUEL _0376057 FUEL SENDER GAUGE ASSEMBLY(w/o Canister Pump Module) A

A25A-FKS FUEL  FUEL SENDER GAUGE ASSEMBLY(w/o Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel sender gauge assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 77020A 3.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 83320 4.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A433831

Disconnect the 2 connectors from the fuel suction plate sub-assembly.


b.

Detach the 2 clamps and disconnect the wire harness.

NOTICE:
·

Do not damage the wire harness.

·

When disengaging each wire harness from the clamp, disengage one wire at a time.




c.
A433832

Detach the 2 clamps and disconnect the wire harness.

NOTICE:
·

Do not damage the wire harness.

·

When disengaging each wire harness from the clamp, disengage one wire at a time.




d.
A433833

Detach the claw and remove the fuel sender gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



Hide 58325E 5.REMOVE REAR FLOOR SERVICE HOLE COVER (for RH Side)

a.

Remove the rear floor service hole cover and butyl tape.


b.
A433867

Disconnect the connector from the fuel tank vent tube assembly.


Hide 77144 6.REMOVE FUEL PUMP GAUGE RETAINER

a.
A433868

Detach the claw and remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A433869C01
1.292,2.99 1.625,2.99 true 1.74,0.458 2.323,0.26 2.323,0.26 2.521,0.26 true 2.031,1.177 2.49,1.51 2.49,1.51 2.688,1.51 true 2.021,0.74 2.688,0.74 true 2.708,1.406 2.917,1.604 0.208,0.198 10 true *c 1.646,2.885 1.854,3.063 0.208,0.177 10 true *d 2.563,0.156 2.792,0.323 0.229,0.167 10 true *a 2.708,0.646 2.958,0.813 0.25,0.167 10 true *b
*a SST (Plate)
*b SST (Bolt)
*c SST (Claw)
*d Insertion Point


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A433870C01
2.021,1.073 2.521,1.073 true 1.854,2.302 2.188,2.302 true 2.344,1.448 2.177,1.448 2.177,1.448 1.844,1.313 true 0.948,0.26 1.115,0.26 1.115,0.26 1.635,0.573 true 0.719,0.74 1.219,0.74 true 0.76,0.156 0.99,0.323 0.229,0.167 10 true *a 0.552,0.646 0.781,0.823 0.229,0.177 10 true *b 2.552,0.969 2.75,1.146 0.198,0.177 10 true *c 2.344,1.344 2.573,1.521 0.229,0.177 10 true *d 1.656,2.208 1.885,2.385 0.229,0.177 10 true *d
*a SST (Handle)
*b SST (Bolt)
*c SST (Plate)
*d SST (Claw)


Install SST (handle) to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel tank vent tube assembly, remove the fuel pump gauge retainer.



Hide 77010 7.REMOVE FUEL TANK VENT TUBE ASSEMBLY

a.
A433871

Disconnect the fuel return vent tube sub-assembly and remove the fuel tank vent tube assembly from the fuel tank assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A433872

Remove the gasket from the fuel tank assembly.


Hide 83320B 8.REMOVE NO. 2 FUEL SENDER GAUGE ASSEMBLY

a.
A433873

Disconnect the connector from the fuel tank vent tube assembly.


b.

Detach the 2 clamps and disconnect the wire harness from the fuel tank vent tube assembly.


c.
A433874

Detach the claw and remove the No. 2 fuel sender gauge assembly.