Home › General › MAINTENANCE › FRONT BRAKE FLEXIBLE HOSE › 2018.10–2019.02
RM3620E _V1 General _076298 MAINTENANCE _0374943 FRONT BRAKE FLEXIBLE HOSE A

MAINTENANCE  FRONT BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47313J 1.INSTALL FRONT FLEXIBLE HOSE

NOTICE:

When installing the front flexible hose, minimize twisting of the hose.


a.
C407443C01
0.552,0.385 0.635,0.385 0.635,0.385 0.688,0.802 true 1.177,2.917 1.271,2.917 1.271,2.917 1.833,2.458 true 1.469,0.333 1.781,0.49 0.313,0.156 10 false *b 0.385,0.302 0.698,0.458 0.313,0.156 10 false *c 0.938,2.833 1.115,3.01 0.177,0.177 10 true *a
*a Identification Mark
*b Torque Wrench Fulcrum Length
*c Union Nut Wrench


Install the front flexible hose with a new clip.

NOTICE:
·

Install the clip as far as it will go.

·

When installing the front flexible hose, face the identification mark to the outside of the vehicle.




b.

Using a union nut wrench, connect the brake line to the front flexible hose while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




c.
C397645C03
0,0 0,0 false
V100135

Hook


Engage the 2 hooks to install the front speed sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor wire harness when installing it.



d.
C407441

Install the front flexible hose and front speed sensor to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



e.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.

·

Do not twist the front flexible hose when installing it.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the ignition switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 3.BLEED BRAKE LINE

Hide 4.INSTALL FRONT WHEEL