Home › General › MAINTENANCE › REAR DISC BRAKE PAD › 2018.10–2020.08
RM3620E _V1 General _076298 MAINTENANCE _0374944 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (w/o vacuum brake booster)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (w/o vacuum brake booster)

·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal. (w/o vacuum brake booster)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (w/o Vacuum Brake Booster)

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>PRECAUTION



Hide 2.REMOVE REAR WHEEL

Hide 4.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 890C0A 6.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 04466 7.REMOVE REAR DISC BRAKE PAD

CAUTION:
C406539

·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C406540C01
2.49,1.344 2.802,1.5 0.313,0.156 10 false *a 2.5,2.604 2.813,2.76 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the rear No. 1 disc brake cylinder slide pin and remove the bolt.


b.

Pull the rear disc brake cylinder assembly upward.


c.
C406541

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 8.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

Remove the rear No. 1 disc brake anti-squeal shim from the rear disc brake pad (inside and outside).

C406538C02
0.083,0.177 7.083,4.542 7,4.365 0.5,1.26 0.729,0.896 false 1.031,1.573 1.26,1.208 false 1.01,3.583 1.24,3.219 false 1.635,3.948 1.865,3.583 false 4.469,3.542 4.698,3.177 false 5.115,3.906 5.344,3.542 false 4.073,1.302 4.302,0.938 false 4.604,1.604 4.833,1.24 false 6.271,2.5 6.5,2.135 false 6.698,2.802 6.865,2.417 false 2.802,2.583 3.031,2.219 false 3.458,4.542 3.458,0.188 false 0.208,0.271 0.521,0.469 0.313,0.198 10 false *A 3.594,0.281 3.906,0.479 0.313,0.198 10 false *B 1.292,1.031 1.604,1.229 0.313,0.198 10 false *1 6.51,1.969 6.823,2.167 0.313,0.198 10 false *1 4.854,1.073 5.167,1.271 0.313,0.198 10 false *1 0.74,0.719 1.052,0.917 0.313,0.198 10 false *2 4.292,0.76 4.604,0.958 0.313,0.198 10 false *2 6.792,2.219 7.01,2.417 0.219,0.198 10 false *2 3.052,2.031 3.365,2.229 0.313,0.198 10 false *3 0.833,3.583 1.146,3.781 0.313,0.198 10 false *4 1.51,3.979 1.823,4.177 0.313,0.198 10 false *4 4.323,3.552 4.635,3.75 0.313,0.198 10 false *4 4.979,3.938 5.292,4.135 0.313,0.198 10 false *4
*A for Type A *B for Type B
*1 Rear No. 1 Disc Brake Anti-squeal Shim *2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Anti-squeal Shim *4 Rear Disc Brake Pad Wear Indicator Plate



b.

Remove the rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (inside and outside).


c.

Remove the rear disc brake anti-squeal shim from the rear disc brake pad (outside).


d.
C406542

Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.