The air conditioning amplifier assembly receives driver side refreshing seat switch (seat blower switch) position signals when the engine switch is on (IG), and then transmits airflow amount signals to each seat climate blower.
for LHD:
for RHD:
If the battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.
for A25A-FKS: Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for M20A-FKS: Click herePower Source / Network>M20A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
If the battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit On AC/Heater Operation" is not displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)".
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST
Inspect the fuse related to this system before inspecting the suspected areas below.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Left Seat Blower | LH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Left Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
C
D
Replace the refreshing seat switch (seat blower switch) with a new or known good one.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for Gasoline Model)>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T25 seatback climate control blower LH connector.
Disconnect the T11 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T25-4 (GND) - T11-4 (BFB-) | Always | Below 1 Ω |
| T25-4 (GND) or T11-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| T25-1 (IG) - T11-5 (CTB) | Always | Below 1 Ω |
| T25-1 (IG) or T11-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| T25-3 (BFB+) - T11-6 (BBS) | Always | Below 1 Ω |
| T25-3 (BFB+) or T11-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control control blower LH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for Gasoline Model)>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly LH) |
Disconnect the seat cushion climate control blower assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T11-1 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| T11-1 (IG) - Body ground | Engine switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T11-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T11 seat cushion climate control blower assembly LH connector.
Disconnect the G46 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T11-7 (SIGN) - G46-14 (LOUT) | Always | Below 1 Ω |
| T11-7 (SIGN) or G46-14 (LOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | G46-14 (LOUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition | ·
Engine switch on (IG) ·
LH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Blower | RH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Right Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
C
D
Replace the refreshing seat switch (seat blower switch) with a new or known good one.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for Gasoline Model)>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S25 seatback climate control blower RH connector.
Disconnect the S11 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S25-4 (GND) - S11-4 (BFB-) | Always | Below 1 Ω |
| S25-4 (GND) or S11-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| S25-1 (IG) - S11-5 (CTB) | Always | Below 1 Ω |
| S25-1 (IG) or S11-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| S25-3 (BFB+) - S11-6 (BBS) | Always | Below 1 Ω |
| S25-3 (BFB+) or S11-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control control blower RH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for Gasoline Model)>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly RH) |
Disconnect the seat cushion climate control blower assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S11-1 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| S11-1 (IG) - Body ground | Engine switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S11-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S11 seat cushion climate control blower assembly RH connector.
Disconnect the G46 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S11-7 (SIGN) - G46-13 (ROUT) | Always | Below 1 Ω |
| S11-7 (SIGN) or G46-13 (ROUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | G46-13 (ROUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition | ·
Engine switch on (IG) ·
RH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG