Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E404413E01
6.125,0.969 6.74,1.167 0.615,0.198 10 false TRLY 6.104,3.51 6.719,3.708 0.615,0.198 10 false RFGO 5.99,4.625 7.135,5.146 1.146,0.521 10 false Main Body ECU (Multiplex Network Body ECU) 6,4.438 7.146,4.958 1.146,0.521 10 false A 3.177,4 5.979,4.365 2.802,0.365 10 false Instrument Panel Junction Block Assembly 4.49,3.271 5.104,3.469 0.615,0.198 10 false FOG RR 4.5,2.177 5.115,2.375 0.615,0.198 10 false FOG RR 1.438,1.281 2.938,1.51 1.5,0.229 10 false DC/DC*1, ALT*2 5.302,1.573 5.917,1.771 0.615,0.198 10 false TAIL 4.594,1.729 5.208,1.927 0.615,0.198 10 false TAIL 0.729,5.906 2.135,6.292 1.406,0.385 10 false Rear Light Socket and Wire (for Driver Side) 0.75,5.74 2.396,6.115 1.646,0.375 10 false R6*3, R7*4 0.76,4.896 2.406,5.271 1.646,0.375 10 false B 0.76,5.396 2.406,5.771 1.646,0.375 10 false E 3,2.594 4.646,2.969 1.646,0.375 10 false 4H 2.917,2.406 4.563,2.781 1.646,0.375 10 false 21*6 3,1.073 4.646,1.448 1.646,0.375 10 false 4K 2.969,0.865 4.615,1.24 1.646,0.375 10 false 1*6 0.271,1.063 1.146,1.469 0.875,0.406 10 false from Auxiliary Battery 4.438,5.135 5.781,5.344 1.344,0.208 10 false *1: for HV Model 4.438,5.406 5.844,5.615 1.406,0.208 10 false *2: for Gasoline Model 0.573,4.885 2.219,5.26 1.646,0.375 10 false 3 0.563,5.396 2.208,5.771 1.646,0.375 10 false 4 5.875,0.969 7.156,1.313 1.281,0.344 10 false 14 5.875,3.51 7.156,3.854 1.281,0.344 10 false 27 2.417,5.906 3.823,6.292 1.406,0.385 10 false Rear Light Lens and Body (for Driver Side) 2.823,5.198 4.229,5.583 1.406,0.385 10 false Rear Fog Light 4.438,5.677 5.844,5.885 1.406,0.208 10 false *3: for LHD 4.438,5.948 5.844,6.156 1.406,0.208 10 false *4: for RHD 2.542,2.594 4.188,2.969 1.646,0.375 10 false 4N 2.5,2.406 4.146,2.781 1.646,0.375 10 false 21*5 4.438,6.229 6.729,6.438 2.292,0.208 10 false *5: for LHD, Manual Transaxle 4.438,6.49 6.729,6.698 2.292,0.208 10 false *6: except LHD, Manual Transaxle 2.542,1.073 4.188,1.448 1.646,0.375 10 false 4M 2.542,0.875 4.188,1.25 1.646,0.375 10 false 1*5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay OFF or ON Light control switch in TAIL position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates (Rear fog lights come on).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE (for Driver Side) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (REAR LIGHT SOCKET AND WIRE (for Driver Side) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

*1: for LHD

*2: for RHD

*3: for LHD, Manual Transaxle

*4: except LHD, Manual Transaxle


a.

Disconnect the R6 rear light socket and wire LH connector.*1


b.

Disconnect the R7 rear light socket and wire RH connector.*2


c.

Disconnect the 4N*3 or 4H*4 instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
R6-3 (B) - 4N-21 Always Below 1 Ω
R6-3 (B) or 4N-21 - Body ground Always 10 kΩ or higher
R6-4 (E) - Body ground Always Below 1 Ω

for LHD except Manual Transaxle:
Tester Connection Condition Specified Condition
R6-3 (B) - 4H-21 Always Below 1 Ω
R6-3 (B) or 4H-21 - Body ground Always 10 kΩ or higher
R6-4 (E) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
R7-3 (B) - 4H-21 Always Below 1 Ω
R7-3 (B) or 4H-21 - Body ground Always 10 kΩ or higher
R7-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E345461C21
1.781,0.406 2.177,0.677 0.396,0.271 3.354,2.229 3.75,2.5 0.396,0.271 4.969,0.396 5.365,0.667 0.396,0.271 4.979,0.063 5.375,0.333 0.396,0.271 1.792,0.094 2.188,0.365 0.396,0.271 2.854,3.292 3.271,2.875 false 4.365,3.281 4.781,2.865 false 1.906,0.469 2.281,0.74 0.375,0.271 10 false 4K 5.094,0.135 5.469,0.406 0.375,0.271 10 false 4N 3.51,2.292 3.885,2.563 0.375,0.271 10 false A 2.677,3.323 3.219,3.594 0.542,0.271 10 false TRLY 4.229,3.313 4.771,3.583 0.542,0.271 10 false RFGO 0.375,0.24 0.75,0.51 0.375,0.271 10 false *a 5.104,0.448 5.479,0.719 0.375,0.271 10 false 4H 5.427,0.125 5.802,0.396 0.375,0.271 10 false *1 5.438,0.438 5.813,0.708 0.375,0.271 10 false *2 1.906,0.156 2.281,0.427 0.375,0.271 10 false 4M 2.24,0.146 2.615,0.417 0.375,0.271 10 false *1 2.25,0.469 2.625,0.74 0.375,0.271 10 false *2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -
*1 for LHD, Manual Transaxle *2 except LHD, Manual Transaxle



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Connect a positive (+) lead from the auxiliary battery to terminal 4M-1*1 or 4K-1*2.

*1: for LHD, Manual Transaxle

*2: except LHD, Manual Transaxle



d.

Connect a negative (-) lead from the auxiliary battery to terminal A-14 (TRLY) and A-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4N-21 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between following terminals
·

4M-1 - A-14 (TRLY)

·

4M-1 - A-27 (RFGO)


11 to 14 V

except LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4H-21 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between following terminals
·

4K-1 - A-14 (TRLY)

·

4K-1 - A-27 (RFGO)


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG