Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2658 Short in Sensor with Motor Power Supply Circuit Problem with the voltage supplied to the position control sensor.
·

Position control ECU assembly (driver seat)

·

Slide motor (front seat adjuster assembly [driver seat])

·

Power seat tilt motor assembly (driver seat)

·

Power seat lifter motor assembly (driver seat)

·

Reclining motor (front seatback frame sub-assembly [driver Seat])

·

Harness or connector



WIRING DIAGRAM

E407951E02
2.083,1.229 3.073,1.5 0.99,0.271 10 false Slide Motor 2.927,0.552 3.5,0.833 0.573,0.281 10 false 2 1.948,0.563 2.521,0.844 0.573,0.281 10 false 3 1.073,2.938 3.823,3.125 2.75,0.188 10 false Power Seat Tilt Motor Assembly (Driver Seat) 1.052,4.031 4.042,4.24 2.99,0.208 10 false Power Seat Lifter Motor Assembly (Driver Seat) 0.969,6.021 4.073,6.229 3.104,0.208 10 false Front Seatback Frame Sub-assembly (Driver Seat) 2.01,5.615 3.042,5.792 1.031,0.177 10 false Reclining Motor 5.229,6.583 5.802,6.865 0.573,0.281 10 false SGND 5.24,5.042 5.813,5.323 0.573,0.281 10 false SSRR 5.229,3.573 5.698,3.76 0.469,0.188 10 false SSRL 5.229,2.365 5.792,2.573 0.563,0.208 10 false SSFV 5.24,0.667 5.813,0.948 0.573,0.281 10 false SSRS 4.906,0.552 5.479,0.833 0.573,0.281 10 false 26 4.938,2.24 5.188,2.427 0.25,0.188 10 false 10 4.948,3.448 5.146,3.635 0.198,0.188 10 false 25 4.927,4.927 5.5,5.208 0.573,0.281 10 false 11 4.938,6.469 5.51,6.75 0.573,0.281 10 false 12 4.885,7.104 6.865,7.521 1.979,0.417 10 false Position Control ECU Assembly (Driver Seat) 1.917,2.24 2.052,2.406 0.135,0.167 10 false 3 1.917,3.469 2.042,3.646 0.125,0.177 10 false 3 1.958,4.948 2.531,5.229 0.573,0.281 10 false 3 2.906,2.24 3.094,2.427 0.188,0.188 10 false 2 2.917,3.448 3.063,3.625 0.146,0.177 10 false 2 2.958,4.927 3.531,5.208 0.573,0.281 10 false 2 2.083,1.083 2.958,1.396 0.875,0.313 10 false T1*1, S1*2 1.073,2.76 1.885,2.938 0.813,0.177 10 false T9*1, S9*2 1.052,3.865 1.948,4.052 0.896,0.188 10 false T12*1, S12*2 2.031,5.458 3.021,5.719 0.99,0.26 10 false T23*1, S23*2 4.885,6.927 6.052,7.188 1.167,0.26 10 false T8*1, S8*2 0.698,7.427 2.385,7.625 1.688,0.198 10 false *1: for LHD 1.896,7.427 3.583,7.625 1.688,0.198 10 false *2: for RHD 1.177,1.604 3.833,1.813 2.656,0.208 10 false Front Seat Adjuster Assembly (Driver Seat)

CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-26 (SSRS) - T1-2 Always Below 1 Ω
T8-26 (SSRS) or T1-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T1-3 Always Below 1 Ω
T8-12 (SGND) or T1-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-26 (SSRS) - S1-2 Always Below 1 Ω
S8-26 (SSRS) or S1-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S1-3 Always Below 1 Ω
S8-12 (SGND) or S1-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)
a.
E407950C11
1.063,0.167 1.479,0.417 0.417,0.25 1.75,0.167 2.167,0.417 0.417,0.25 0.156,0.083 0.396,0.333 0.24,0.25 10 false *a 1.875,0.219 2.25,0.49 0.375,0.271 10 false S1 1.177,0.208 1.635,0.406 0.458,0.198 10 false T1 1.51,0.177 1.708,0.365 0.198,0.188 10 false *A 2.198,0.188 2.448,0.365 0.25,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Slide Motor [Front Seat Adjuster Assembly (Driver Seat)])


Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T1-2 - T1-3 Slide switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S1-2 - S1-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT TILT MOTOR ASSEMBLY [DRIVER SEAT])

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT TILT MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-10 (SSFV) - T9-2 Always Below 1 Ω
T8-10 (SSFV) or T9-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T9-3 Always Below 1 Ω
T8-12 (SGND) or T9-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-10 (SSFV) - S9-2 Always Below 1 Ω
S8-10 (SSFV) or S9-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S9-3 Always Below 1 Ω
S8-12 (SGND) or S9-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)
a.
E407950C12
1.052,0.198 1.469,0.448 0.417,0.25 1.854,0.198 2.271,0.448 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.177,0.24 1.635,0.438 0.458,0.198 10 false T9 1.979,0.24 2.438,0.438 0.458,0.198 10 false S9 1.521,0.219 1.76,0.469 0.24,0.25 10 false *A 2.323,0.219 2.563,0.469 0.24,0.25 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Power Seat Tilt Motor Assembly [Driver Seat])


Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T9-2 - T9-3 Front vertical switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S9-2 - S9-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-25 (SSRL) - T12-2 Always Below 1 Ω
T8-25 (SSRL) or T12-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T12-3 Always Below 1 Ω
T8-12 (SGND) or T12-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-25 (SSRL) - S12-2 Always Below 1 Ω
S8-25 (SSRL) or S12-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S12-3 Always Below 1 Ω
S8-12 (SGND) or S12-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.
E407950C13
1.75,0.167 2.167,0.417 0.417,0.25 1.073,0.167 1.49,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.844,0.219 2.219,0.49 0.375,0.271 10 false S12 1.177,0.219 1.635,0.417 0.458,0.198 10 false T12 1.521,0.198 1.708,0.375 0.188,0.177 10 false *A 2.198,0.198 2.406,0.375 0.208,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Power Seat Lifter Motor Assembly [Driver Seat])


Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T12-2 - T12-3 Rear lifter switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S12-2 - S12-3 Rear lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-11 (SSRR) - T23-2 Always Below 1 Ω
T8-11 (SSRR) or T23-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T23-3 Always Below 1 Ω
T8-12 (SGND) or T23-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-11 (SSRR) - S23-2 Always Below 1 Ω
S8-11 (SSRR) or S23-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S23-3 Always Below 1 Ω
S8-12 (SGND) or S23-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.
E407950C14
1.781,0.167 2.198,0.417 0.417,0.25 1.104,0.167 1.521,0.417 0.417,0.25 0.156,0.115 0.396,0.365 0.24,0.25 10 false *a 1.875,0.219 2.25,0.49 0.375,0.271 10 false S23 1.208,0.219 1.521,0.417 0.313,0.198 10 false T23 1.552,0.188 1.75,0.365 0.198,0.177 10 false *A 2.25,0.188 2.51,0.365 0.26,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Reclining Motor [Front Seatback Frame Sub-assembly (Driver Seat)])


Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T23-2 - T23-3 Reclining switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S23-2 - S23-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

11.REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

11.REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
a.

Replace the power seat tilt motor assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER SEAT TILT MOTOR ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Replace the power seat lifter motor assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

15.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])
15.REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])
a.

Replace the slide motor (front seat adjuster assembly [driver seat]) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)] WAS DEFECTIVE)

NG

17.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])
17.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])
a.

Replace the reclining motor (front seatback frame sub-assembly [driver seat]) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR DTC
18.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)] WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)