Home › Brake › BRAKE (REAR) › REAR BRAKE › 2018.10–2019.02
RM3620E _54 Brake _076412 BRAKE (REAR) _0375827 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (w/o vacuum brake booster)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (w/o vacuum brake booster)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431B 1.INSTALL REAR DISC

a.
C406522C01
1,1.927 1.563,1.51 true 1,1.938 1.542,1.469 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C399996C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 4.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C406534C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.


c.
C406535C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.


d.
C406518C01
2.26,1.49 2.073,1.781 true 2.417,0.573 2.292,0.323 true 2.25,1.26 2.5,1.469 0.25,0.208 10 true *1 2.417,0.625 2.615,0.865 0.198,0.24 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


e.

Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.


Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.

·

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.



HINT:

If the rear disc brake pad has an identification mark, be sure to confirm the installation location.

C406536C01
0.26,0.177 6.969,4.615 6.708,4.438 3.688,4.604 3.688,0.188 false 1.198,3.458 1.781,3.458 true 2.708,3.25 3.083,3.25 true 4.26,3.354 4.844,3.354 true 5.906,3.313 6.271,3.313 true 0.469,0.354 0.781,0.552 0.313,0.198 10 false *A 3.885,0.365 4.198,0.563 0.313,0.198 10 false *B 3.125,3.167 3.438,3.365 0.313,0.198 10 false *a 0.99,3.375 1.302,3.573 0.313,0.198 10 false *b 4.052,3.271 4.365,3.469 0.313,0.198 10 false *d 6.323,3.219 6.635,3.417 0.313,0.198 10 false *c
*A for Type A *B for Type B
*a Inner Side (Orange) *b Outer Side (Yellow green)
*c Inner Side (Blue) *d Outer Side (Yellow green)




Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C407911C01
2.292,0.458 2.604,0.656 0.313,0.198 10 false *a 2.406,2.344 2.719,2.542 0.313,0.198 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 new bolts in the order shown in the illustration.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 46310B 9.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY LH

Hide 890C0A 10.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 47319F 11.CONNECT REAR FLEXIBLE HOSE LH

a.

Connect the rear flexible hose LH to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Install the rear flexible hose LH lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


c.

Install battery hole cover.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


d.

Install rear No. 2 floor board.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


e.

Install deck board assembly.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


f.

Turn the ignition switch on (READY).


g.

Depress the brake pedal and release it.



Hide 13. BLEED BRAKE LINE

Hide 14.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY (w/ Vacuum Brake Booster)

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder.


NOTICE:
·

Perform air bleeding while maintaining the brake fluid level between the MAX and MIN lines on the brake fluid reservoir.

·

Do not allow brake fluid to contact any painted surface. If brake fluid leaks onto any painted surface, immediately wash it off.



HINT:
·

Use the same procedure for the RH and LH sides, except where indicated.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake assembly, the bolt can be reused during the bleeding procedure. After air bleeding is complete, replace the bolt with a new one.



a.

Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/ Vacuum Brake Booster)>TEST MODE PROCEDURE


b.
C400765

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly LH.


c.
C409085C01
2.49,1.344 2.802,1.5 0.313,0.156 10 false *a 2.5,2.604 2.813,2.76 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting.(*1)

NOTICE:

Keep the rear no. 2 disc brake cylinder slide pin free of foreign matter.



d.
C408159

Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)


e.
C409086C01
2.469,1.333 2.781,1.531 0.313,0.198 10 false *a 2.531,2.583 2.844,2.781 0.313,0.198 10 false *b
*a Turn
*b Hold


Temporarily install the rear disc brake cylinder assembly with the 2 bolts.(*3)


f.

Remove the center cowl top ventilator louver.



g.

Remove the brake master cylinder reservoir filler cap.



h.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




i.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.(*4)


j.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.(*5)


k.

Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.



l.

Tighten the bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


m.

Install the rear disc brake cylinder assembly with a 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


n.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly LH.


o.

Inspect for brake fluid leaks.


p.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID(w/ Vacuum Brake Booster)>ON-VEHICLE INSPECTION


q.

Install the brake master cylinder reservoir filler cap assembly.

Click hereGeneral>MAINTENANCE>BRAKE FLUID(w/ Vacuum Brake Booster)>REPLACEMENT


r.

Install the center cowl top ventilator louver.



Hide 15.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY (w/o Vacuum Brake Booster)

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.


HINT:
·

Use the same procedure for RHD and LHD vehicles., except where indicated.

·

The procedure listed below is for LHD vehicles.

·

While performing air bleeding of the rear disc brake cylinder assembly, the bolts can be reused during the bleeding procedure. After air bleeding is complete, replace the bolts with new ones.



a.

Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE


b.
C400765

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly LH.


c.

Remove the center cowl top ventilator louver.

i.
C400729

Disengage the 3 hooks and separate the hood to cowl top seal from the cowl top ventilator louver sub-assembly.


ii.
C400733

Disengage the 2 claws and 2 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



d.
C400750

Remove the brake master cylinder reservoir filler cap assembly.


e.

Add brake fluid to the brake master cylinder reservoir assembly until the brake fluid level is between the MAX and MIN lines on the brake master cylinder reservoir assembly.

NOTICE:
·

Make sure that there is sufficient brake fluid in the brake master cylinder reservoir assembly.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




f.

Connect the GTS to the DLC3 with the ignition switch off.


g.

Turn the ignition switch on (IG).


h.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125
HINT:

Do not apply the parking brake even if instructed by the GTS.



i.
C409085C02
2.49,1.344 2.802,1.5 0.313,0.156 10 false *a 2.5,2.604 2.813,2.76 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting.


j.
C408159

Hold the rear disc brake cylinder assembly with the rear disc brake cylinder mounting horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)


k.

Temporarily install the rear disc brake cylinder assembly with the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.(*3)


l.

Using the GTS, perform air bleeding.(*4)


m.

Follow the GTS instructions to bleed the air from the brake fluid.(*5)

NOTICE:

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brake lines.



n.

Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.



o.

Tighten the bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


p.

Install the rear disc brake cylinder assembly with a new 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


q.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.



s.

Turn the GTS off and turn the ignition switch off.


t.

Disconnect the GTS from the DLC3.


u.

Inspect for brake fluid leaks.


v.

Inspect and adjust the brake fluid level in the brake master cylinder reservoir assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (w/o Vacuum Brake Booster)>ON-VEHICLE INSPECTION


w.

Install the brake master cylinder reservoir filler cap assembly.


x.

Install the center cowl top ventilator louver.


Hide 16.INSTALL REAR WHEEL