Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0375834 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the dynamic cruise control on/off signal and various control signals to the hybrid vehicle control ECU assembly.

·

The hybrid vehicle control ECU assembly controls the dynamic radar cruise control system according to the signals received from the steering pad switch assembly.


WIRING DIAGRAM

C374512E23
3.979,2.646 5.677,3.313 1.698,0.667 10 false Spiral Cable Sub-assembly 1,2.646 2.917,2.979 1.917,0.333 10 false Steering Pad Switch Assembly 3.073,1.385 3.688,1.583 0.615,0.198 10 false MAIN 2.177,1.385 2.792,1.583 0.615,0.198 10 false CANCEL 1.313,1.385 1.927,1.583 0.615,0.198 10 false +RES 0.469,1.385 1.083,1.583 0.615,0.198 10 false -SET 3.854,2.083 4.167,2.281 0.313,0.198 10 false z6 3.844,0.875 4.156,1.073 0.313,0.198 10 false z6 3.885,0.677 4.042,0.875 0.156,0.198 10 false 2 3.854,1.875 4.083,2.073 0.229,0.198 10 false 12 4.667,0.792 5.125,0.99 0.458,0.198 10 false CCS 4.677,2 5.135,2.198 0.458,0.198 10 false ECC 5.51,0.875 5.969,1.073 0.458,0.198 10 false G20 5.521,2.083 5.979,2.281 0.458,0.198 10 false G20 5.563,0.667 5.823,0.875 0.26,0.208 10 false 13 5.604,1.875 5.76,2.073 0.156,0.198 10 false 2 6.417,0.885 6.875,1.083 0.458,0.198 10 false CCS 6.167,0.771 6.427,0.958 0.26,0.188 10 false 14 6.198,2.573 7.073,2.927 0.875,0.354 10 false A30*1 G63*2 6.208,2.76 7.135,3.302 0.927,0.542 10 false Hybrid Vehicle Control ECU Assembly 3.323,1.979 3.719,2.188 0.396,0.208 10 false ECC 3.323,0.771 3.688,0.979 0.365,0.208 10 false CCS 1.156,3.292 2.031,3.646 0.875,0.354 10 false *1: for LHD 2.104,3.281 2.979,3.635 0.875,0.354 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (CRUISE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise1 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 21,22,23,1
OK:

The value of each Data List item changes according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the G20 spiral able sub-assembly connector.


b.

Disconnect the A30*1 or G63*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance for LHD:
Tester Connection Condition Specified Condition
G20-13 (CCS) - A30-14 (CCS) Always Below 1 Ω
G20-2 (ECC) - Body ground Always Below 1 Ω
G20-13 (CCS) or A30-14 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance for RHD:
Tester Connection Condition Specified Condition
G20-13 (CCS) - G63-14 (CCS) Always Below 1 Ω
G20-2 (ECC) - Body ground Always Below 1 Ω
G20-13 (CCS) or G63-14 (CCS) - Body ground Always 10 kΩ or higher



d.

Connect the A30*1 or G63*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD


e.

Connect the G20 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR