Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift state is park (P) and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift state park (P) and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal Pulse

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check

·

L Code Check



WIRING DIAGRAM

B538106E01
0.208,0.302 1.104,1.094 0.896,0.792 10 false from Auxiliary Battery 1.667,0.552 2.083,0.719 0.417,0.167 10 false STOP 2.24,0.292 2.49,0.458 0.25,0.167 10 false 7 2.417,0.375 2.594,0.573 0.177,0.198 10 false B 2.427,0.792 2.833,0.979 0.406,0.188 10 false GND 2.24,1.198 2.552,1.365 0.313,0.167 10 false A40 2.24,1.344 4.24,1.563 2,0.219 10 false Stop Light Switch Assembly 2.865,0.615 3.042,0.781 0.177,0.167 10 false IC 3.188,0.396 3.375,0.563 0.188,0.167 10 false L 3.375,0.396 3.583,0.594 0.208,0.198 10 false 3 4.969,0.292 5.229,0.458 0.26,0.167 10 false 25 4.958,0.5 5.271,0.698 0.313,0.198 10 false M7 5.323,0.396 5.823,0.604 0.5,0.208 10 false STP1 6.219,0.646 6.406,0.833 0.188,0.188 10 false IC 5.729,1.573 6.01,1.771 0.281,0.198 10 false +B 6.25,3.625 6.469,3.813 0.219,0.188 10 false IC 5.313,3.344 5.667,3.5 0.354,0.156 10 false ST2 5,3.229 5.24,3.396 0.24,0.167 10 false 27 4.969,4.521 6.74,5.104 1.771,0.583 10 false Certification ECU (Smart Key ECU Assembly) 0.906,3.354 1.313,3.542 0.406,0.188 10 false ST2 1.396,3.25 1.625,3.448 0.229,0.198 10 false 4 1.313,3.458 1.781,3.708 0.469,0.25 10 false A30 1.406,3.875 1.688,4.063 0.281,0.188 10 false 7 1.313,4.083 1.646,4.24 0.333,0.156 10 false A29 0.917,4.104 1.323,4.292 0.406,0.188 10 false STP 0.208,5.156 2.083,5.479 1.875,0.323 10 false Hybrid Vehicle Control ECU Assembly 1.938,2.969 4.26,3.531 2.323,0.563 10 false Shift Lock Control Unit Assembly 5.01,5.625 5.417,5.813 0.406,0.188 10 false A42 5.01,5.802 6.979,6.135 1.969,0.333 10 false Skid Control ECU Assembly 5.208,5.344 5.49,5.5 0.281,0.156 10 false 6 5.427,5.417 5.833,5.604 0.406,0.188 10 false STP2 2.26,0.688 2.51,0.854 0.25,0.167 10 false 2 4.927,2.083 5.313,2.302 0.385,0.219 10 false G54 4.969,1.875 5.208,2.042 0.24,0.167 10 false 22 1.906,2.792 2.313,2.979 0.406,0.188 10 false G26 3.365,1.948 3.771,2.135 0.406,0.188 10 false 3 3.083,1.948 3.635,2.177 0.552,0.229 10 false P2 5.323,1.958 5.677,2.115 0.354,0.156 10 false P 4.927,3.448 5.24,3.635 0.313,0.188 10 false G54 6.25,2.021 6.469,2.208 0.219,0.188 10 false IC 5.521,3.031 5.802,3.229 0.281,0.198 10 false +B 0.219,6.042 1.49,6.354 1.271,0.313 10 false *1: for LHD 0.229,6.396 1.5,6.708 1.271,0.313 10 false *2: for RHD 1.781,3.24 2.01,3.438 0.229,0.198 10 false 4 1.708,3.458 2.167,3.656 0.458,0.198 10 false G63 1.375,3.677 1.688,3.875 0.313,0.198 10 false *1 1.76,3.677 2.073,3.875 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift state park (P).


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes: Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

C

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (ACC))

D

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG))

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
3.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal State of brake pedal ON or OFF ON: Shift state park (P)
OFF: Shift state not park (P)
·

Use this item to determine if the shift position switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status OFF or ON OFF: The power switch is not pressed
ON: With the shift state park (P) and the brake pedal depressed, the power switch is pressed and held
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

7.CHECK STEERING LOCK
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

for LHD:

Disconnect the A30 hybrid vehicle control ECU assembly connector.


c.

for RHD:

Disconnect the G63 hybrid vehicle control ECU assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G54-27 (ST2) - A30-4 (ST2) Always Below 1 Ω
G54-27 (ST2) or A30-4 (ST2) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G54-27 (ST2) - G63-4 (ST2) Always Below 1 Ω
G54-27 (ST2) or G63-4 (ST2) - Other terminals and body ground Always 10 kΩ or higher



e.

Connect the G54 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B498244C47
1.604,0.115 1.969,0.354 0.365,0.24 1.042,1.927 1.24,1.927 1.24,1.927 1.24,1.063 false 1.656,0.167 2,0.365 0.344,0.198 10 false G54 0.729,1.844 1.323,2.042 0.594,0.198 10 false ST2 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G54-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approximately 3 seconds has elapsed, the power switch is released 8.5 V or higher → 1 V or less



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK STEERING LOCK
a.

Check that the steering unlocks when the power switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Hybrid Control System cannot Start))

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift state park (P).


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Immobiliser System does not Operate Properly)

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.
B510755C11
1.531,0.073 1.948,0.333 0.417,0.26 2.188,1.917 2.063,1.917 2.063,1.917 1.823,1.115 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.625,0.135 1.938,0.333 0.313,0.198 10 false G54 2.26,1.865 2.573,2.063 0.313,0.198 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G54-22 (P) - Other terminals and body ground Shift state park (P) → Shift state not park (P) 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G26 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-22 (P) - G26-3 (P2) Always Below 1 Ω
G54-22 (P) or G26-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B498244C48
1.604,0.115 1.969,0.354 0.365,0.24 2.406,1.948 2.156,1.948 2.156,1.948 1.823,1.104 false 1.656,0.156 2,0.354 0.344,0.198 10 false G54 2.469,1.896 3.063,2.094 0.594,0.198 10 false P 0.146,0.125 0.74,0.323 0.594,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-22 (P) - Other terminals and body ground Power switch off 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
E409581C06
1.469,0.115 1.969,0.365 0.5,0.25 0.917,1.833 1.083,1.833 1.083,1.833 1.271,1.354 true 2.667,1.833 2.479,1.833 2.479,1.833 2.302,1.365 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 1.594,0.156 1.906,0.313 0.313,0.156 10 false A40 2.75,1.76 3.063,1.917 0.313,0.156 10 false B 0.583,1.76 1.031,1.969 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A40-7 (B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.

for LHD:

Disconnect the A29 and A30 hybrid vehicle control ECU assembly connectors.


c.

for RHD:

Disconnect the A29 and G63 hybrid vehicle control ECU assembly connectors.


d.

Disconnect the A42 skid control ECU connector.


e.

Disconnect the G26 shift lock control unit assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-25 (STP1) - A40-3 (L) Always Below 1 Ω
M7-25 (STP1) or A40-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY