Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor



HINT:

Use this procedure to troubleshoot the malfunction that ACC mode of all the ECUs is not available.

When ACC mode of some ECUs is not available, check the ACC power source circuit related to the malfunctioning ECUs.


WIRING DIAGRAM

E414767E03
2.063,4.115 4.875,4.885 2.813,0.771 10 false Instrument Panel Junction Block Assembly 5.5,3.833 7.094,4.865 1.594,1.031 10 false Certification ECU (Smart Key ECU Assembly) 5.479,3.625 6.271,4.448 0.792,0.823 10 false G54 6.094,2.729 6.563,3.25 0.469,0.521 10 false 16 6.354,2.854 6.938,3.406 0.583,0.552 10 false ACCD 5.344,2.823 5.927,3.375 0.583,0.552 10 false 4A 5.365,2.646 5.948,3.198 0.583,0.552 10 false 30 5.302,1.823 5.885,2.375 0.583,0.552 10 false 4K 5.323,1.635 5.906,2.188 0.583,0.552 10 false 1 4.344,3.125 5.615,3.594 1.271,0.469 10 false ACC 3.073,2.656 4.344,3.125 1.271,0.469 10 false ECU-ACC 1.635,2.313 2.219,2.865 0.583,0.552 10 false 40 1.615,2.479 2.198,3.031 0.583,0.552 10 false 4A 1.615,2.833 2.198,3.385 0.583,0.552 10 false 4D 1.667,2.667 2.25,3.219 0.583,0.552 10 false 3 2.052,1.219 2.719,2.479 0.667,1.26 10 false SFT LOCK-ACC 3.25,0.5 4.844,1.531 1.594,1.031 10 false from Auxiliary Battery 0.156,2.313 1.406,3.531 1.25,1.219 10 false to Each ACC power supply 2.063,1.906 2.771,3.104 0.708,1.198 10 false P/OUTLET NO.1 2.938,1.771 5.167,2.99 2.229,1.219 10 false to Power outret socket assembly ACC power supply 2.906,1.042 5.25,2.302 2.344,1.26 10 false to Shift lock cantrol unit assembly ACC power supply

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start, Power Source Control / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the 4K instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
C412262C02
1.375,0.708 1.75,0.979 0.375,0.271 4.365,0.688 4.74,0.958 0.375,0.271 6.26,0.813 6.667,1.042 0.406,0.229 4.469,0.719 4.781,0.917 0.313,0.198 10 false 4D 1.469,0.75 1.781,0.948 0.313,0.198 10 false 4A 6.333,0.823 6.646,1.021 0.313,0.198 10 false 4K
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 4A-30.


d.

Connect a negative (-) lead from the auxiliary battery to terminal 4D-3.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - 4A-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG