The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
Use the same procedure described for the LH side.
When performing removal for the black out tape, disconnect the negative (-) auxiliary battery terminal after fully opening the front door glass.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD
65351A
4.REMOVE BATTERY HOLE COVER
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69278B
6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
74642A
7.REMOVE FRONT DOOR ASSIST GRIP COVER LH
8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
67602
10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
68172A
11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
68193C
12.REMOVE FRONT DOOR FRONT BELT SEAL LH
67832
13.REMOVE FRONT DOOR SERVICE HOLE COVER LH
68102
14.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
67664C
15.REMOVE DOOR FRAME GARNISH LH
68151D
16.REMOVE FRONT DOOR GLASS RUN LH
67402F
17.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
68126
18.REMOVE FRONT DOOR FIX WINDOW GLASS LH
75712B
19.REMOVE FRONT DOOR BELT MOULDING LH
67862
20.REMOVE FRONT DOOR WEATHERSTRIP LH
75966B
21.REMOVE FRONT DOOR NO. 4 STRIPE LH
When removing the front door No. 4 stripe LH, if it is difficult to remove, heat the adhesive of the front door No. 4 stripe LH and front door panel using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| Front Door No. 4 Stripe LH | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front door panel and front door No. 4 stripe LH excessively.
Pull back on one of the ends of the front door No. 4 stripe LH to remove it.
When pulling on the front door No. 4 stripe LH, pull it parallel to the front door panel.
75986G
22.REMOVE FRONT DOOR OUTSIDE STRIPE LH
When removing the front door outside stripe LH, if it is difficult to remove, heat the adhesive of the front door outside stripe LH and front door panel using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| Front Door Outside Stripe LH | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front door panel and front door outside stripe LH excessively.
Pull back on one of the ends of the front door outside stripe LH to remove it.
When pulling on the front door outside stripe LH, pull it parallel to the front door panel.
75922M
23.REMOVE NO. 1 BLACK OUT TAPE LH
When removing the No. 1 black out tape LH, if it is difficult to remove, heat the adhesive of the No. 1 black out tape LH and front door panel using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| No. 1 Black Out Tape LH | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front door panel and No. 1 black out tape LH excessively.
Pull back on one of the ends of the No. 1 black out tape LH to remove it.
When pulling on the No. 1 black out tape LH, pull it parallel to the front door panel.