Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door)
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0376602 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.



PROCEDURE

Hide 75954A 2.INSTALL REAR INNER BLACK OUT TAPE LH

a.

Refer to the illustration to position a new inner rear black out tape LH.

B524075C01
1.344,0.802 1.25,1.167 true 5.344,1.156 6.063,0.979 true 1.573,3.115 1.771,2.99 false 0.865,4.156 1.208,4.021 false 0.646,7.323 1.021,7.563 0.375,0.24 12 false *A 1.875,7.323 2.25,7.563 0.375,0.24 12 false *B 1.271,0.594 1.583,0.792 0.313,0.198 10 false *a 5.146,1.094 5.458,1.292 0.313,0.198 10 false *b 4.344,1.656 4.521,1.875 0.177,0.219 10 false A 1.531,2.208 1.688,2.406 0.156,0.198 10 false B 1.125,4.271 1.281,4.469 0.156,0.198 10 false C 3.792,6.688 3.948,6.885 0.156,0.198 10 false D 5.604,6.615 5.76,6.813 0.156,0.198 10 false E 4.854,3.75 5.01,3.948 0.156,0.198 10 false a 5.26,3.896 5.417,4.094 0.156,0.198 10 false a 0.938,4.563 1.708,4.76 0.771,0.198 10 false a - a 1.781,2.854 2.094,3.052 0.313,0.198 10 false *c 0.708,4.083 1.021,4.281 0.313,0.198 10 false *c 3.75,6.167 4.063,6.365 0.313,0.198 10 false *d 5.521,6.167 5.833,6.365 0.313,0.198 10 false *e
*A for RH Side *B for LH Side
*a Point A *b Point B
*c Edge of Curved Surface *d When Removing Rear Door Weatherstrip LH
*e When Installing Rear Door Weatherstrip LH - -


Standard Measurement:
Area Measurement Area Measurement
A 4.0 mm (0.157 in.) B 1.6 to 3.6 mm (0.0629 to 0.1417 in.)
C 1.0 mm (0.0393 in.) D 5.5 mm (0.216 in.)
E 5.0 mm (0.216 in.) - -



b.

Remove the release paper and install the inner rear black out tape LH.

HINT:

Align the point (A) on the inner rear black out tape LH with the point (B) on the door frame and install the inner rear black out tape LH.



Hide 75988E 3.INSTALL REAR DOOR OUTSIDE STRIPE LH

a.

Refer to the illustration to position a new rear door outside stripe LH.

B524076C01
1.531,6.625 1.875,6.625 false 2.448,1.25 3.198,1.115 true 6.542,1.333 6.219,1.542 false 5.313,1.281 4.917,1.427 false 5.115,6.25 5.375,6.469 0.26,0.219 12 false *A 6.354,6.24 6.625,6.448 0.271,0.208 12 false *B 1.354,6.531 1.667,6.729 0.313,0.198 10 false *a 2.167,2.813 2.323,3.01 0.156,0.198 10 false a 2.167,3.198 2.323,3.396 0.156,0.198 10 false a 5.469,2.104 6.24,2.302 0.771,0.198 10 false a - a 4.906,0.906 5.063,1.104 0.156,0.198 10 false A 6.479,1.729 6.635,1.927 0.156,0.198 10 false B 4.375,2.906 4.542,3.073 0.167,0.167 10 false C 5.865,2.74 6.031,2.906 0.167,0.167 10 false D 2.26,1.198 2.573,1.396 0.313,0.198 10 false *b 6.573,1.208 6.885,1.406 0.313,0.198 10 false *c 4.74,1.354 5.052,1.552 0.313,0.198 10 false *c 3.708,2.698 3.906,2.885 0.198,0.188 10 false *d 5.438,2.688 5.635,2.875 0.198,0.188 10 false *e
*A for RH Side *B for LH Side
*a Point A *b Point B
*c Edge of Curved Surface *d When Removing Rear Door Frame Garnish LH
*e When Installing Rear Door Frame Garnish LH - -


Standard Measurement:
Area Measurement Area Measurement
A 1.6 to 3.6 mm (0.0629 to 0.1417 in.) B 1.0 mm (0.0393 in.)
C 15 mm (0.590 in.) D 10 mm (0.393 in.)



b.

Remove the release paper and install the rear door outside stripe LH.

HINT:

Align the point (A) on the rear door outside stripe LH with the point (B) on the door frame and install the rear door outside stripe LH.



Hide 75978H 4.INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH

a.

Refer to the illustration to position a new rear door lower outside stripe LH.

B524077C02
5.969,5.833 6.854,6.031 0.885,0.198 6.135,7.719 6.927,7.979 0.792,0.26 5.958,4.521 6.844,4.719 0.885,0.198 5.063,2.792 4.865,2.677 false 2.073,0.813 2.573,1.094 true 5.542,5.521 5.729,5.521 5.729,5.521 6.135,7.708 false 5.427,4.552 5.948,4.604 false 5.969,5.823 5.792,5 5.792,5 5.479,4.979 false 4.469,0.344 4.844,0.583 0.375,0.24 12 false *A 5.708,0.344 6.083,0.583 0.375,0.24 12 false *B 4.469,2.563 5.385,2.76 0.917,0.198 10 false *a, *c 2.625,1.083 3.542,1.281 0.917,0.198 10 false *b, *c 4.865,4.542 5.021,4.74 0.156,0.198 10 false a 5.24,4.469 5.396,4.667 0.156,0.198 10 true a 4.948,5 5.104,5.198 0.156,0.198 10 false b 5.323,4.938 5.479,5.135 0.156,0.198 10 true b 5.042,5.49 5.198,5.688 0.156,0.198 10 false c 5.385,5.427 5.542,5.625 0.156,0.198 10 true c 1.635,4.594 2.406,4.792 0.771,0.198 10 false a - a 1.448,6.563 2.458,6.771 1.01,0.208 10 false b - b, c - c 0.927,2.521 1.323,2.802 0.396,0.281 10 false *d 2.833,2.542 3.229,2.823 0.396,0.281 10 false *e 1.26,7.146 1.656,7.427 0.396,0.281 10 false *f 3.344,7.115 3.74,7.396 0.396,0.281 10 false *g 1.844,1.542 2,1.74 0.156,0.198 10 false A 2.896,2.323 3.052,2.521 0.156,0.198 10 false B 0.688,3.948 0.844,4.146 0.156,0.198 10 false C 0.656,5.802 0.813,6 0.156,0.198 10 false D 3.094,4.406 3.25,4.604 0.156,0.198 10 false E 3.104,6.219 3.26,6.417 0.156,0.198 10 false F 2.615,7.854 2.844,8.073 0.229,0.219 10 false G 4.583,7.781 4.813,8 0.229,0.219 10 false H
*A for RH Side *B for LH Side
*a Point A *b Point B
*c Edge of Curved Surface *d When Removing Rear Door Frame Garnish LH
*e When Installing Rear Door Frame Garnish LH *f When Removing Rear door Weatherstrip LH
*g When Installing Rear door Weatherstrip LH - -


Standard Measurement:
Area Measurement Area Measurement
A 40 mm (1.57 in.) B 10 mm (0.393 in.)
C 1.2 mm (0.0472 in.) D -1.0 to 1.0 mm (-0.0393 to 0.0393 in.)
E 3.0 mm (0.118 in.) F 3.0 mm (0.118 in.)
G 5.0 mm (0.196 in.) H 5.0 mm (0.196 in.)



b.

Remove the release paper and install the rear door lower outside stripe LH.

HINT:

Align the point (A) on the rear door lower outside stripe LH with the point (B) on the door frame and install the rear door lower outside stripe LH.



Hide 68104 6.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 68124B 7.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

Hide 67408E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 9.INSTALL REAR DOOR GLASS RUN LH

Hide 75722A 10.INSTALL REAR DOOR BELT MOULDING LH

Hide 67674A 11.INSTALL REAR DOOR FRAME GARNISH LH

Hide 67842E 12.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 68199 13.INSTALL REAR DOOR REAR BELT SEAL LH

Hide 68174A 14.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 67604 15.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 16.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 74646A 17.INSTALL DOOR ASSIST GRIP COVER LH

Hide 69278C 18.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 20.INSTALL BATTERY HOLE COVER

Hide 58416K 21.INSTALL REAR NO. 2 FLOOR BOARD

Hide 58410B 22.INSTALL DECK BOARD ASSEMBLY

Hide 23. INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 24. CHECK POWER WINDOW CONTROL SYSTEM

Hide 25. CHECK POWER DOOR LOCK CONTROL SYSTEM