Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window assembly LH or RH is tapped or broken, the sensor will set off the alarm.

WIRING DIAGRAM

B605072E02
1.104,1.479 1.563,1.646 0.458,0.167 10 false SSR+ 1.104,2.01 1.563,2.177 0.458,0.167 10 false SSR- 1.667,1.813 2.073,2.01 0.406,0.198 10 false 1 1.677,1.281 2.135,1.448 0.458,0.167 10 false 1 1.604,1.479 2.063,1.646 0.458,0.167 10 false M25 0.615,4.771 1.708,5.635 1.094,0.865 10 false Quarter Window Assembly LH (Glass Breakage Sensor) 1.104,3.948 1.563,4.115 0.458,0.167 10 false SSR+ 1.125,4.479 1.583,4.646 0.458,0.167 10 false SSR- 1.604,3.948 2.063,4.115 0.458,0.167 10 false N41 1.698,4.302 2.156,4.469 0.458,0.167 10 false 1 4.99,2.292 5.417,2.458 0.427,0.167 10 false G45 4.74,1.354 4.969,1.521 0.229,0.167 10 false 1 5,1.375 5.771,1.573 0.771,0.198 10 false GPBS 5,2.448 6.625,2.833 1.625,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.219,4.875 5.677,5.042 0.458,0.167 10 false R12 5.135,4.396 5.365,4.563 0.229,0.167 10 false 1 5.313,4.51 5.771,4.677 0.458,0.167 10 false SSR+ 5.813,4.5 6.198,4.688 0.385,0.188 10 false SSR- 6.229,4.385 6.385,4.573 0.156,0.188 10 false 2 5.219,5.073 6.427,5.698 1.208,0.625 10 false Back Door Glass (Glass Breakage Sensor) 0.625,2.292 1.771,3.292 1.146,1 10 false Quarter Window Assembly RH (Glass Breakage Sensor) 1.698,3.708 2.156,3.875 0.458,0.167 10 false 1 1.604,2.031 2.063,2.198 0.458,0.167 10 false M26 1.604,4.5 2.063,4.667 0.458,0.167 10 false N42 5.417,0.833 5.771,1 0.354,0.167 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (GLASS BREAK SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sealed Glas Brak Sen Glass breakage sensor connecting With or Without With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-
Body Electrical > Main Body > Data List
Tester Display
Sealed Glas Brak Sen
50003 123 208
OK:

"With" (glass breakage sensor operating) appears on GTS screen.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
B605531C05
1.469,0.292 1.906,0.552 0.438,0.26 2.177,1.74 1.979,1.74 1.979,1.74 1.74,1.177 true 1.552,0.344 2.01,0.542 0.458,0.198 10 false M25 2.26,1.656 3.031,1.865 0.771,0.208 10 false SSR+ 0.198,0.135 0.969,0.344 0.771,0.208 10 false *a
*a Front view of wire harness connector
(to Quarter Window Assembly RH (Glass Breakage Sensor))


Disconnect the quarter window assembly RH (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
M25-1 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

3.CHECK QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

NG

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR))
3.CHECK QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)
a.
B605531C06
1.49,0.385 1.885,0.615 0.396,0.229 2.083,1.896 1.938,1.896 1.938,1.896 1.75,1.177 true 1.563,0.417 2.021,0.615 0.458,0.198 10 false N41 2.177,1.833 2.781,2.042 0.604,0.208 10 false SSR+ 0.167,0.115 0.771,0.323 0.604,0.208 10 false *a
*a Front view of wire harness connector
(to Quarter Window Assembly LH (Glass Breakage Sensor))


Disconnect the quarter window assembly LH (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
N41-1 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

4.CHECK QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) - QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR))
4.CHECK QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)
a.
B605723C01
1.49,0.396 1.917,0.635 0.427,0.24 1.271,1.802 1.458,1.802 1.458,1.802 1.625,1.25 true 1.583,0.438 2.042,0.635 0.458,0.198 10 false R12 0.167,0.177 0.625,0.375 0.458,0.198 10 false *a 0.844,1.708 1.302,1.906 0.458,0.198 10 false SSR+
*a Front view of wire harness connector
(to Back door Glass (Glass Breakage Sensor))


Disconnect the back door glass (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
R12-1 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (GLASS BREAKAGE SENSOR) - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) - BACK DOOR GLASS (GLASS BREAKAGE SENSOR))
5.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (GLASS BREAKAGE SENSOR) - BODY GROUND)
a.
B605723C03
1.5,0.438 1.917,0.677 0.417,0.24 2.323,1.823 2.083,1.823 2.083,1.823 1.813,1.25 true 1.573,0.479 2.115,0.969 0.542,0.49 10 false R12 2.385,1.74 2.969,1.958 0.583,0.219 10 false SSR- 0.198,0.156 0.656,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Back Door Glass (Glass Breakage Sensor))


Disconnect the back door glass (glass breakage sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R12-2 (SSR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) - BACK DOOR GLASS (GLASS BREAKAGE SENSOR))
a.

Disconnect the N42 quarter window assembly LH (glass breakage sensor) connector.


b.

Disconnect the R12 back door glass (glass breakage sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N42-1 (SSR-) - R12-1 (SSR+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) - QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR))
a.

Disconnect the M26 quarter window assembly RH (glass breakage sensor) connector.


b.

Disconnect the N41 quarter window assembly LH (glass breakage sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M26-1 (SSR-) - N41-1 (SSR+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR))
a.

Disconnect the M25 quarter window assembly RH (glass breakage sensor) connector.


b.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-1 (GPBS) - M25-1 (SSR+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR