Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER (for HV Model)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374862 CONDENSER(for HV Model) A

HEATING / AIR CONDITIONING  CONDENSER(for HV Model)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 88460 1.INSTALL COOLER CONDENSER ASSEMBLY

a.
E406583C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the cooler condenser assembly.

NOTICE:

Do not damage the cooler condenser assembly, radiator assembly (for inverter coolant) and radiator assembly when installing the cooler condenser assembly.


HINT:

If a new cooler condenser assembly is installed, add compressor oil to the condenser as follows.


Capacity:

Add 40 cc (1.35 fl. oz)


Compressor Oil:

ND-OIL 11 or equivalent



Hide 88711 2.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape wrapped around the connection of the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.
E406581

Connect the No. 1 cooler refrigerant discharge hose with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




Hide 16593B 3.INSTALL NO. 1 RADIATOR AIR GUIDE RH

a.
E406580C01
0.104,0.094 0.479,0.333 0.375,0.24 12 false *A 0.104,2.438 0.479,2.677 0.375,0.24 12 false *B
*A w/o Grille Shutter
*B w/ Grille Shutter


Attach the guide to install the No. 1 radiator air guide RH.


b.

Attach the clip.


Hide G9010A 4.CONNECT RADIATOR ASSEMBLY (for Inverter Coolant)

a.

Move the radiator assembly so that the No. 3 inverter cooling hoses are aligned with the No. 1 radiator air guide RH.

NOTICE:

Do not apply excessive force to the No. 3 inverter cooling hose and No. 4 inverter cooling hose.


E406584C01
0,0 0,0 false
V113147

Connect in this Direction (1)
V113148

Connect in this Direction (2)



b.
E406578

Install the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Attach the claw to connect the radiator assembly.


Hide 88710E 5.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape wrapped around the connection of the air conditioning tube and accessory assembly and the air conditioning tube and accessory assembly.


b.
E396375C03
2,1.74 2,1.406 true 1.25,1.781 1.25,1.531 true 1.542,1.396 2.188,0.635 2.188,0.635 1.542,0.844 true 1.917,1.74 2.229,1.896 0.313,0.156 10 false *1 1.167,1.792 1.479,1.948 0.313,0.156 10 false *2 2.219,0.521 2.531,0.677 0.313,0.156 10 false *a
*1 Air Conditioning Tube and Accessory Assembly
*2 Piping Clamp
*a Groove


Install a new piping clamp to the air conditioning tube and accessory assembly.

NOTICE:
·

Securely engage the piping clamp to the groove of the air conditioning tube and accessory assembly.

·

Do not open the piping clamp more than the diameter of the air conditioning tube and accessory assembly when installing it.

·

Do not install the piping clamp with the large diameter section facing the wrong direction.

·

Before installing, remove any foreign matter adhered to the fitting area.




c.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



d.

Install the 2 O-rings to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



e.

Connect the air conditioning tube and accessory assembly to the cooler condenser assembly.

NOTICE:
·

Connect the parts by holding the pipe, not the piping clamp.

·

Do not apply excessive force to the air conditioning tube and accessory assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)

·

Before connecting, remove any foreign matter adhered to the fitting area.



E406585C01
3.667,1.531 3.667,1.198 true 6.219,1.823 6.219,1.49 true 4.094,1.688 4.094,1.354 true 5.271,3.656 5.104,3.656 5.104,3.656 5.104,3.323 true 3.583,1.531 3.896,1.729 0.313,0.198 10 false *1 6.135,1.823 6.448,2.021 0.313,0.198 10 false *2 4.01,1.688 4.323,1.885 0.313,0.198 10 false *3 5.281,3.563 5.594,3.76 0.313,0.198 10 false *a
*1 Air Conditioning Tube and Accessory Assembly *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Large Diameter Section of Piping Clamp - -
V113147

Install in this Direction - -



f.

Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.

NOTICE:
·

Securely insert until the piping clamp claw enters the cooler condenser assembly.

E406586C01
2.719,3.406 2.719,3.073 true 3.188,3.604 3.188,3.271 true 4.385,3.604 4.385,3.271 true 2.635,3.396 2.948,3.594 0.313,0.198 10 false *1 4.302,3.604 4.615,3.802 0.313,0.198 10 false *2 3.104,3.604 3.417,3.802 0.313,0.198 10 false *3 0.948,0.365 1.26,0.563 0.313,0.198 10 false *a 3.781,0.365 4.094,0.563 0.313,0.198 10 false *b
*1 Air Conditioning Tube and Accessory Assembly *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a OK *b NG


·

When inserting, make sure that a click sound is heard.

·

Check that the air conditioning tube and accessory assembly is securely connected by pulling it.




Hide 53205 6.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Attach the upper radiator support sub-assembly to the 2 radiator support cushions and install the upper radiator support sub-assembly with the 4 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

When installing the upper radiator support sub-assembly, do not damage the cooler condenser assembly, radiator assembly (for inverter coolant) and radiator assembly.


E406575C01
3.281,1.344 3.281,1.01 true 5.844,1.635 5.844,1.302 true 3.188,1.323 3.365,1.5 0.177,0.177 10 true *1 5.75,1.615 5.927,1.792 0.177,0.177 10 true *1
*1 Radiator Support Cushion - -



b.

Attach the clamp.


c.

w/ Engine Hood Courtesy Switch

i.
E406574

Attach the clamp.



Hide 53630 7.CONNECT HOOD LOCK CONTROL CABLE ASSEMBLY

a.
E406573

Connect the hood lock control cable assembly to the clamp.


Hide 17750A 8.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 86570 9.INSTALL VEHICLE APPROACHING SPEAKER ASSEMBLY (w/ Vehicle Proximity Notification System)

Hide 86520 10.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 53019F 11.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)

Hide 52021 12.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

Hide 13.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT