Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0376982 SFI SYSTEM(w/o Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E66
0.99,0.833 2.802,1.135 1.813,0.302 10 false from EFI-MAIN NO. 4 Fuse 0.938,1.177 2.698,1.531 1.76,0.354 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>ECM Power Source Circuit

·

VC Output Circuit

A435154E01
0.552,0.604 2.063,1.073 1.51,0.469 10 false Throttle Body with Motor Assembly 0.552,0.365 2.063,0.833 1.51,0.469 10 false C15 0.531,1.979 2.042,2.448 1.51,0.469 10 false F4 0.531,2.146 2.271,2.635 1.74,0.49 10 false Crankshaft Position Sensor 0.531,3.385 2.167,3.896 1.635,0.51 10 false Camshaft Position Sensor (for Intake Camshaft) 0.542,3.219 2.052,3.688 1.51,0.469 10 false C10 0.531,4.708 2.167,5.219 1.635,0.51 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.542,4.542 2.052,5.01 1.51,0.469 10 false C12 0.552,6.042 2.26,6.563 1.708,0.521 10 false Manifold Absolute Pressure Sensor 0.552,5.875 2.063,6.344 1.51,0.469 10 false C16 0.438,7.094 1.948,7.563 1.51,0.469 10 false E5 6.281,0.177 6.677,0.521 0.396,0.344 10 false 5 V 2.958,0.417 3.354,0.76 0.396,0.344 10 false VC 2.969,0.781 3.365,1.125 0.396,0.344 10 false E2 2.885,1.135 3.281,1.479 0.396,0.344 10 false VTA 2.813,1.51 3.208,1.854 0.396,0.344 10 false VTA2 2.781,2.031 3.177,2.375 0.396,0.344 10 false VCNE 2.865,2.396 3.26,2.74 0.396,0.344 10 false NE- 2.833,2.76 3.229,3.104 0.396,0.344 10 false NE+ 2.938,3.313 3.333,3.656 0.396,0.344 10 false VC 2.865,3.656 3.26,4 0.396,0.344 10 false VVI- 2.823,4.031 3.219,4.375 0.396,0.344 10 false VVI+ 2.854,4.625 3.25,4.969 0.396,0.344 10 false VC2 2.792,4.969 3.188,5.313 0.396,0.344 10 false VVE- 2.74,5.344 3.135,5.688 0.396,0.344 10 false VVE+ 2.938,5.885 3.333,6.229 0.396,0.344 10 false VC 2.865,6.625 3.26,6.969 0.396,0.344 10 false PIM 2.927,6.25 3.323,6.594 0.396,0.344 10 false E2 2.938,7.208 3.333,7.552 0.396,0.344 10 false VC 2.948,7.573 3.344,7.917 0.396,0.344 10 false E2 2.833,7.948 3.229,8.292 0.396,0.344 10 false PEL 3.25,0.333 3.646,0.677 0.396,0.344 10 false 2 3.25,0.667 3.646,1.01 0.396,0.344 10 false 4 3.26,1.031 3.656,1.375 0.396,0.344 10 false 1 3.25,1.385 3.646,1.729 0.396,0.344 10 false 3 3.271,1.906 3.667,2.25 0.396,0.344 10 false 3 3.271,2.271 3.667,2.615 0.396,0.344 10 false 2 3.25,2.635 3.646,2.979 0.396,0.344 10 false 1 3.281,3.188 3.677,3.531 0.396,0.344 10 false 3 3.271,3.552 3.667,3.896 0.396,0.344 10 false 2 3.271,3.906 3.667,4.25 0.396,0.344 10 false 1 3.271,4.49 3.667,4.833 0.396,0.344 10 false 3 3.271,4.865 3.667,5.208 0.396,0.344 10 false 2 3.271,5.219 3.667,5.563 0.396,0.344 10 false 1 3.271,5.76 3.667,6.104 0.396,0.344 10 false 3 3.26,6.135 3.656,6.479 0.396,0.344 10 false 1 3.271,6.49 3.667,6.833 0.396,0.344 10 false 2 3.271,7.104 3.667,7.448 0.396,0.344 10 false 1 3.26,7.448 3.656,7.792 0.396,0.344 10 false 3 3.271,7.833 3.667,8.177 0.396,0.344 10 false 2 4.885,0.417 5.281,0.76 0.396,0.344 10 false C40 4.885,0.781 5.281,1.125 0.396,0.344 10 false C40 4.885,1.146 5.281,1.49 0.396,0.344 10 false C40 4.885,1.51 5.281,1.854 0.396,0.344 10 false C40 4.885,2.021 5.281,2.365 0.396,0.344 10 false C40 4.896,2.385 5.292,2.729 0.396,0.344 10 false C40 4.885,2.76 5.281,3.104 0.396,0.344 10 false C40 4.885,3.292 5.281,3.635 0.396,0.344 10 false C40 4.885,3.667 5.281,4.01 0.396,0.344 10 false C40 4.885,4.031 5.281,4.375 0.396,0.344 10 false C40 4.875,4.625 5.271,4.969 0.396,0.344 10 false C40 4.885,5.885 5.281,6.229 0.396,0.344 10 false C40 4.896,4.99 5.292,5.333 0.396,0.344 10 false C40 4.875,5.344 5.271,5.688 0.396,0.344 10 false C40 4.885,6.25 5.281,6.594 0.396,0.344 10 false C40 4.896,6.615 5.292,6.958 0.396,0.344 10 false C40 4.885,7.219 5.281,7.563 0.396,0.344 10 false C40 4.896,7.583 5.292,7.927 0.396,0.344 10 false C40 4.885,7.948 5.281,8.292 0.396,0.344 10 false C40 4.896,0.219 5.292,0.563 0.396,0.344 10 false 109 4.896,0.594 5.292,0.938 0.396,0.344 10 false 110 4.896,0.969 5.292,1.313 0.396,0.344 10 false 108 4.938,1.323 5.333,1.667 0.396,0.344 10 false 87 4.896,1.833 5.292,2.177 0.396,0.344 10 false 116 4.896,2.208 5.292,2.552 0.396,0.344 10 false 115 4.938,2.573 5.333,2.917 0.396,0.344 10 false 93 4.938,3.104 5.333,3.448 0.396,0.344 10 false 88 4.938,3.49 5.333,3.833 0.396,0.344 10 false 89 4.938,3.844 5.333,4.188 0.396,0.344 10 false 90 4.896,4.427 5.292,4.771 0.396,0.344 10 false 113 4.896,4.802 5.292,5.146 0.396,0.344 10 false 114 4.938,5.167 5.333,5.51 0.396,0.344 10 false 91 4.896,5.698 5.292,6.042 0.396,0.344 10 false 121 4.885,6.073 5.281,6.417 0.396,0.344 10 false 119 4.896,6.438 5.292,6.781 0.396,0.344 10 false 120 4.938,7.031 5.333,7.375 0.396,0.344 10 false 84 4.938,7.396 5.333,7.74 0.396,0.344 10 false 61 4.896,7.771 5.292,8.115 0.396,0.344 10 false 107 5.281,0.313 5.677,0.656 0.396,0.344 10 false VCTA 5.292,0.677 5.688,1.021 0.396,0.344 10 false ETA 5.292,1.146 5.688,1.49 0.396,0.344 10 false VTA1 5.302,1.51 5.698,1.854 0.396,0.344 10 false VTA2 5.281,1.917 5.677,2.26 0.396,0.344 10 false VCNE 5.281,2.281 5.677,2.625 0.396,0.344 10 false NE- 5.292,2.74 5.688,3.083 0.396,0.344 10 false NE+ 5.281,3.188 5.677,3.531 0.396,0.344 10 false VCV1 5.292,3.552 5.688,3.896 0.396,0.344 10 false VV1- 5.292,4.031 5.688,4.375 0.396,0.344 10 false VV1+ 5.292,4.5 5.688,4.844 0.396,0.344 10 false VCE1 5.302,4.865 5.698,5.208 0.396,0.344 10 false EV1- 5.292,5.344 5.688,5.688 0.396,0.344 10 false EV1+ 5.292,5.781 5.927,6.125 0.635,0.344 10 false VCPM 5.292,6.625 5.688,6.969 0.396,0.344 10 false PIM 5.292,6.146 5.688,6.49 0.396,0.344 10 false EPIM 5.292,7.104 5.906,7.469 0.615,0.365 10 false VCPF 5.302,7.948 5.698,8.292 0.396,0.344 10 false PFL 5.302,7.479 5.823,7.771 0.521,0.292 10 false EPFL 5.74,8.438 6.135,8.781 0.396,0.344 10 false ECM 0.438,7.271 2.656,7.792 2.219,0.521 10 false Fuel Pressure Sensor (for Low Pressure Side)

A436249E01
5.76,8.438 6.188,8.677 0.427,0.24 10 false ECM 0.552,5.5 0.979,5.74 0.427,0.24 10 false C5 0.573,5.698 2.167,6.115 1.594,0.417 10 false Engine Oil Pressure and Temperature Sensor 0.615,7.25 1.042,7.49 0.427,0.24 10 false F2 0.635,7.448 2.219,7.906 1.583,0.458 10 false Fuel Pressure Sensor (for High Pressure Side) 0.542,4.01 1.854,4.427 1.313,0.417 10 false Mass Air Flow Meter Sub-assembly 0.542,3.833 0.969,4.073 0.427,0.24 10 false C17 0.51,0.677 0.938,0.917 0.427,0.24 10 false A65 0.51,0.833 2.104,1.417 1.594,0.583 10 false Accelerator Pedal Sensor Assembly 2.958,0.604 3.385,0.844 0.427,0.24 10 false VCPA 3.063,1.604 3.49,1.844 0.427,0.24 10 false EPA 3.042,2.604 3.469,2.844 0.427,0.24 10 false VPA 3.458,0.5 3.885,0.74 0.427,0.24 10 false 4 3.458,1.01 3.885,1.25 0.427,0.24 10 false 1 3.458,1.521 3.885,1.76 0.427,0.24 10 false 5 3.479,2.01 3.906,2.25 0.427,0.24 10 false 2 3.458,2.51 3.885,2.75 0.427,0.24 10 false 6 3.458,3.01 3.885,3.25 0.427,0.24 10 false 3 4.927,0.604 5.354,0.844 0.427,0.24 10 false A24 4.917,3.708 5.344,3.948 0.427,0.24 10 false C40 4.948,0.406 5.375,0.646 0.427,0.24 10 false 57 4.948,0.917 5.375,1.156 0.427,0.24 10 false 60 4.969,1.406 5.396,1.646 0.427,0.24 10 false 56 4.958,1.927 5.385,2.167 0.427,0.24 10 false 59 4.969,2.427 5.396,2.667 0.427,0.24 10 false 55 4.969,2.917 5.396,3.156 0.427,0.24 10 false 58 4.958,3.5 5.385,3.74 0.427,0.24 10 false 78 4.958,3.938 5.385,4.177 0.427,0.24 10 false 79 4.917,4.344 5.344,4.583 0.427,0.24 10 false 101 4.917,4.771 5.344,5.01 0.427,0.24 10 false 102 4.958,5.313 5.385,5.552 0.427,0.24 10 false 99 4.958,5.729 5.385,5.969 0.427,0.24 10 false 100 4.969,6.156 5.396,6.396 0.427,0.24 10 false 122 4.969,7.073 5.396,7.313 0.427,0.24 10 false 98 4.958,7.479 5.385,7.719 0.427,0.24 10 false 96 4.927,7.865 5.354,8.104 0.427,0.24 10 false 97 3.073,3.708 3.5,3.948 0.427,0.24 10 false VCC 3.052,4.125 3.479,4.365 0.427,0.24 10 false E2G 3.156,4.552 3.583,4.792 0.427,0.24 10 false FG 3.083,4.979 3.51,5.219 0.427,0.24 10 false THA 3.156,7.281 3.719,7.51 0.563,0.229 10 false VC 3.167,7.677 3.594,7.917 0.427,0.24 10 false E2 3.083,8.063 3.51,8.302 0.427,0.24 10 false PR 3.01,6.771 3.438,7.01 0.427,0.24 10 false TOUT 5.313,3.604 5.771,3.833 0.458,0.229 10 false VCVG 5.313,5.406 5.74,5.646 0.427,0.24 10 false VCPE 5.323,7.188 5.75,7.427 0.427,0.24 10 false VCPR 2.958,1.104 3.385,1.344 0.427,0.24 10 false VCP2 2.99,2.104 3.417,2.344 0.427,0.24 10 false EPA2 2.969,3.104 3.396,3.344 0.427,0.24 10 false VPA2 3.167,5.531 3.594,5.771 0.427,0.24 10 false VC 2.99,6.344 3.417,6.583 0.427,0.24 10 false POUT 3.458,4.438 3.885,4.677 0.427,0.24 10 false 1 3.479,5.844 3.906,6.083 0.427,0.24 10 false 2 3.469,7.167 3.896,7.406 0.427,0.24 10 false 1 3.469,4.021 3.896,4.26 0.427,0.24 10 false 2 3.469,6.26 3.896,6.5 0.427,0.24 10 false 1 3.49,7.958 3.917,8.198 0.427,0.24 10 false 3 3.458,3.604 3.885,3.844 0.427,0.24 10 false 3 3.479,5.417 3.771,5.625 0.292,0.208 10 false 3 3.49,7.552 3.917,7.792 0.427,0.24 10 false 2 3.448,4.875 3.875,5.115 0.427,0.24 10 false 4 5.302,0.521 5.729,0.76 0.427,0.24 10 false VCPA 5.302,1.021 5.729,1.26 0.427,0.24 10 false VCP2 5.313,1.51 5.74,1.75 0.427,0.24 10 false EPA 5.302,2.01 5.729,2.25 0.427,0.24 10 false EPA2 5.313,2.625 5.74,2.865 0.427,0.24 10 false VPA 5.313,3.115 5.74,3.354 0.427,0.24 10 false VPA2 5.313,4.021 5.74,4.26 0.427,0.24 10 false E2G 5.323,4.552 5.75,4.792 0.427,0.24 10 false VG 5.323,4.969 5.75,5.208 0.427,0.24 10 false THA 5.323,5.844 5.75,6.083 0.427,0.24 10 false EPEO 5.313,6.354 5.74,6.594 0.427,0.24 10 false PEO 5.333,8.042 5.76,8.281 0.427,0.24 10 false PR 5.323,7.563 5.75,7.802 0.427,0.24 10 false EPR 4.927,1.115 5.354,1.354 0.427,0.24 10 false A24 4.938,1.604 5.365,1.844 0.427,0.24 10 false A24 4.938,2.115 5.365,2.354 0.427,0.24 10 false A24 4.927,2.615 5.354,2.854 0.427,0.24 10 false A24 4.927,3.115 5.354,3.354 0.427,0.24 10 false A24 4.927,4.125 5.354,4.365 0.427,0.24 10 false C40 4.917,4.542 5.344,4.781 0.427,0.24 10 false C40 4.927,4.969 5.354,5.208 0.427,0.24 10 false C40 4.927,5.51 5.354,5.75 0.427,0.24 10 false C40 4.917,5.927 5.344,6.167 0.427,0.24 10 false C40 4.927,6.354 5.354,6.594 0.427,0.24 10 false C40 4.927,7.281 5.354,7.521 0.427,0.24 10 false C40 4.927,7.677 5.354,7.917 0.427,0.24 10 false C40 4.917,8.063 5.344,8.302 0.427,0.24 10 false C40 4.938,6.771 5.365,7.01 0.427,0.24 10 false C40 5.333,6.76 5.948,6.958 0.615,0.198 10 false THEO 4.969,6.573 5.427,6.771 0.458,0.198 10 false 123 3.073,5.927 3.531,6.125 0.458,0.198 10 false GND 3.458,6.667 3.615,6.865 0.156,0.198 10 false 4


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
A435797C02
0.281,1.479 0.417,1.479 0.417,1.479 1.365,0.813 false 0.135,0.104 0.448,0.26 0.313,0.156 10 false *1 0.104,1.396 0.417,1.552 0.313,0.156 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI NO. 1 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block and junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

9.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for low pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

13.CHECK HARNESS AND CONNECTOR

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the engine oil pressure and temperature sensor connector.


g.

Disconnect the accelerator pedal sensor assembly connector.


h.

Disconnect the mass air flow meter sub-assembly connector.


i.

Disconnect the fuel pressure sensor (for high pressure side) connector.


j.

Disconnect the fuel pressure sensor (for low pressure side) connector.


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-109 (VCTA) - Body ground Always 10 kΩ or higher
C40-116 (VCNE) - Body ground Always 10 kΩ or higher
C40-88 (VCV1) - Body ground Always 10 kΩ or higher
C40-113 (VCE1) - Body ground Always 10 kΩ or higher
C40-121 (VCPM) - Body ground Always 10 kΩ or higher
C40-99 (VCPE) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-60 (VCP2) - Body ground Always 10 kΩ or higher
C40-78 (VCVG) - Body ground Always 10 kΩ or higher
C40-98 (VCPR) - Body ground Always 10 kΩ or higher
C40-84 (VCPF) - Body ground Always 10 kΩ or higher



m.

Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.

HINT:

Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



n.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-9 (+B) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-35 (+B2) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-9 (+B) - Body ground Always 10 kΩ or higher
A24-35 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR