Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
87114B
1.INSTALL HEATER COVER
88625
2.INSTALL NO. 1 COOLER THERMISTOR
88501
3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.
| *A | for Type A | *B | for Type B |
Attach the guide.
While inserting the No. 1 cooler thermistor into the guide, attach the guide and claw as shown in the illustration.
| *a | No. 1 Cooler Thermistor Lead Wire | - | - |
|
Secure the lead wire between the guide | - | - |
Install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case with the 2 screws.
88515
4.INSTALL COOLER EXPANSION VALVE
Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and cooler expansion valve.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
ND-OIL 8 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
| *A | for Type A |
| *B | for Type B |
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)
88899L
5.INSTALL COOLING UNIT PARTS
87107A
6.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
87124B
7.INSTALL HEATER CLAMP
88897M
8.INSTALL HEATER PIPE GROMMET
87050D
9.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
87050C
10.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
for Automatic Air Conditioning System:
Align the fitting part and gear alignment part of the heater case with the fitting part and gear alignment part of the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
| *a | Gear Alignment Part | - | - |
for Manual Air Conditioning System:
Align the fitting part of the heater case with the fitting part of the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
| *A | for Automatic Air Conditioning System |
| *B | for Manual Air Conditioning System |
Attach the guide.
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
82210K
11.INSTALL AIR CONDITIONING HARNESS ASSEMBLY
Attach the clamp and guide.
| *A | for LHD | *B | for RHD |
| *a | Clamp | *b | Guide |
Connect each connector to install the air conditioning harness assembly.
88539C
12.INSTALL NO. 2 COOLER UNIT DRAIN HOSE (Available as Supply Part)
88539J
13.INSTALL DRAIN COOLER HOSE
88625Q
14.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) (for Automatic Air Conditioning System)
88897P
15.INSTALL ASPIRATOR (for Automatic Air Conditioning System)
88898D
16.INSTALL GROMMET (for Manual Air Conditioning System)
Attach the claw to install the grommet.
Firmly push it down into the heater case until a "click" sound is heard.
87201B
17.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
87130D
18.INSTALL BLOWER ASSEMBLY