Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for A25A-FXS)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374936 COMPRESSOR(for A25A-FXS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for A25A-FXS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E408292

When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 120 to 135 cc (4.06 to 4.56 fl. oz)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor with motor assembly)


NOTICE:
·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.




Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.
E409903C01
0,0 0,0 false
V100135

Connector (B)
V100136

Slide
V100155

Green-colored Lock


Remove the insulating tape from the connector (B).


b.

Connect the connector (B) and slide the green-colored lock as shown in the illustration to securely lock it.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



c.
E408289C01
0,0 0,0 false
V100135

Bolt
V100136

Stud Bolt


Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts and bolt.

Torque:
Stud Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
E408293C01
2.573,1.969 2.667,2.135 0.094,0.167 10 true 1 0.865,0.031 0.958,0.198 0.094,0.167 10 true 2 0.917,1.969 1.01,2.135 0.094,0.167 10 true 3
V100135

Bolt
V100136

Nut


Install the compressor with motor assembly with the bolt and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and nuts in the order shown in the illustration, or temporarily install 3 of them, and then tighten them in the order 1, 2 and 3.



e.
E408287C01
0,0 0,0 false
V100135

Connector (A)


Connect the connector (A).


Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape wrapped around the connection of the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.
E408286

Connect the No. 1 cooler refrigerant discharge hose with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape wrapped around the connection of the suction hose sub-assembly and suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.
E408285

Connect the suction hose sub-assembly.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

Do not apply excessive force to the suction hose sub-assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




Hide 53875A 5.INSTALL FRONT FENDER LINER RH

Hide 53736E 6.INSTALL FRONT FENDER APRON SEAL RH

Hide 76621D 7.INSTALL FRONT FENDER MUDGUARD RH (w/ Mudguard)

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>MUDGUARD>INSTALLATION


Hide 53896B 9.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 10.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 75601A 11.INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>WHEEL OPENING MOULDING (for Front)>INSTALLATION


Hide 12.INSTALL FRONT WHEEL RH

Hide 14.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT