Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for Off Road Package) › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377204 FRONT BUMPER(for Off Road Package) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Off Road Package)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (for Gasoline Model) (Click here)

HINT:
·

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

Hide 53896B 1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

HINT:

Use the same procedure as for the RH and LH sides.


Hide 75602A 3.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

a.
B560730C03
0,0 0,0 false
V100135

Screw
V100136

Clip


Remove the screw.


b.

Remove the 2 clips.


c.
B525604C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape around the front fender moulding sub-assembly LH.


d.
B526105C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull back the edge of the front fender liner LH and detach the claw by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.




e.
B525572C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Detach the clip and disconnect the front fender moulding sub-assembly LH as shown in the illustration.


Hide 75601A 4.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the RH and LH sides.


Hide 5.REMOVE FRONT BUMPER ASSEMBLY

a.
B525990

Remove the 4 bolts.


b.
B526106

Remove the 6 screws.


c.
B526107C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape around the front bumper assembly.

HINT:

Use the same procedure as for the RH and LH sides.



d.
B560731

Remove the 2 clips.

HINT:

Use the same procedure as for the RH and LH sides.



e.
B526109C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw.

HINT:

Use the same procedure as for the RH and LH sides.



f.
B526110

Pull back the edge of the front fender liner LH and disconnect the 2 connectors.


g.
B526111C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front bumper assembly.


h.
B525574

Remove the 2 clips from the front fender moulding sub-assembly LH.

NOTICE:

If the front bumper assembly has been removed, replace the clip with a new one.


HINT:

Use the same procedure as for the RH and LH sides.



Hide 52536 6.REMOVE FRONT BUMPER SIDE RETAINER LH

HINT:

Perform the following procedure only when replacement of a front bumper side retainer LH is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Off Road Package)>REMOVAL


Hide 52535 7.REMOVE FRONT BUMPER SIDE RETAINER RH

HINT:
·

Perform the following procedure only when replacement of a front bumper side retainer RH is necessary.

·

Use the same procedure as for the RH and LH sides.



Hide 52614 8.REMOVE FRONT BUMPER NO. 2 ENERGY ABSORBER

HINT:

Perform the following procedure only when replacement of a front bumper No. 2 energy absorber is necessary.


a.
B525546C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the front bumper No. 2 energy absorber.


Hide 52021 9.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

HINT:

Perform the following procedure only when replacement of a front bumper reinforcement sub-assembly is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Off Road Package)>REMOVAL


Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

HINT:

Perform the following procedure only when replacement of a front bumper extension sub-assembly LH and RH or front bumper lower absorber is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Off Road Package)>REMOVAL


Hide 52618 11.REMOVE FRONT BUMPER LOWER ABSORBER

HINT:

Perform the following procedure only when replacement of a front bumper lower absorber is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Off Road Package)>REMOVAL


Hide 52103C 12.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY LH

HINT:

Perform the following procedure only when replacement of a front bumper extension sub-assembly LH is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Off Road Package)>REMOVAL


Hide 52102F 13.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
·

Perform the following procedure only when replacement of a front bumper extension sub-assembly RH is necessary.

·

Use the same procedure as for the RH and LH sides.