The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.
When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
53896B
1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Use the same procedure described for the RH side.
for Short Type:
Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL
for Long Type:
Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL
53895B
2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Use the same procedure as for the RH and LH sides.
75602A
3.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH
|
Screw |
|
Clip |
Remove the screw.
Remove the 2 clips.
|
Protective Tape |
Put protective tape around the front fender moulding sub-assembly LH.
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull back the edge of the front fender liner LH and detach the claw by pushing the area indicated by the arrow in the illustration with a finger.
Do not apply excessive force when pulling back the front fender liner LH.
To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.
0,0 0,0
false
|
Place Hand Here |
|
Remove in this Direction |
Detach the clip and disconnect the front fender moulding sub-assembly LH as shown in the illustration.
75601A
4.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
5.REMOVE FRONT BUMPER ASSEMBLY
Remove the 4 bolts.
Remove the 6 screws.
|
Protective Tape |
Put protective tape around the front bumper assembly.
Use the same procedure as for the RH and LH sides.
Remove the 2 clips.
Use the same procedure as for the RH and LH sides.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw.
Use the same procedure as for the RH and LH sides.
| *A | w/ Headlight Cleaner System |
|
Connector |
|
Headlight Cleaner Hose |
Pull back the edge of the front fender liner LH and disconnect the 2 connectors.
w/ Headlight Cleaner System:
Detach the headlight cleaner hose clamp.
Disconnect the headlight cleaner hose.
Prepare a container before performing the procedure.
|
Remove in this Direction |
Detach the claw and remove the front bumper assembly.
Remove the 2 clips from the front fender moulding sub-assembly LH.
If the front bumper assembly has been removed, replace the clip with a new one.
Use the same procedure as for the RH and LH sides.
52536
6.REMOVE FRONT BUMPER SIDE RETAINER LH
Perform the following procedure only when replacement of a front bumper side retainer LH is necessary.
| *a | 90° |
|
Rotation Direction |
|
Remove in this Direction |
Remove the bolt.
Using a screwdriver, turn the clip 90° and detach the clip and claw to remove the front bumper side retainer LH as shown in the illustration.
52535
7.REMOVE FRONT BUMPER SIDE RETAINER RH
Perform the following procedure only when replacement of a front bumper side retainer RH is necessary.
Use the same procedure as for the RH and LH sides.
52614
8.REMOVE FRONT BUMPER NO. 2 ENERGY ABSORBER
Perform the following procedure only when replacement of a front bumper No. 2 energy absorber is necessary.
|
Remove in this Direction |
Detach the guide and remove the front bumper No. 2 energy absorber.
16561C
9.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator To Support Seal)
Perform the following procedure only when replacement of a front bumper reinforcement sub-assembly is necessary.
Click hereEngine / Hybrid System>A25A-FXS (COOLING)>RADIATOR>REMOVAL
52021
10.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Perform the following procedure only when replacement of a front bumper reinforcement sub-assembly is necessary.
Detach the wire harness clamp.
|
Remove in this Direction |
Remove the 6 bolts and front bumper reinforcement sub-assembly as shown in the illustration.
52132A
11.REMOVE FRONT BUMPER NO. 2 REINFORCEMENT (for HV Model)
Perform the following procedure only when replacement of a front bumper No. 2 reinforcement is necessary.
Remove the 4 nuts and front bumper No. 2 reinforcement.
51441
12.REMOVE NO. 1 ENGINE UNDER COVER
Perform the following procedure only when replacement of a front bumper extension sub-assembly LH and RH or front bumper lower absorber is necessary.
for Short Front Fender Front Splash Shield:
Remove the 4 screws and 2 bolts.
| *A | for Short Front Fender Front Splash Shield | - | - |
|
Bolt |
|
Screw |
for Long Front Fender Front Splash Shield:
Remove the 2 screws and 2 bolts.
|
Remove in this Direction |
Detach the guide and remove the No. 1 engine under cover.
52618
13.REMOVE FRONT BUMPER LOWER ABSORBER (for Gasoline Model)
Perform the following procedure only when replacement of a front bumper lower absorber is necessary.
Remove the 5 bolts.
|
Remove in this Direction |
Detach the guide and remove the front bumper lower absorber as shown in the illustration.
52618
14.REMOVE FRONT BUMPER LOWER ABSORBER (for HV Model)
Perform the following procedure only when replacement of a front bumper lower absorber is necessary.
Remove the clip.
|
Remove in this Direction |
Detach the claw and remove the front bumper lower absorber.
52103C
15.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY LH
Perform the following procedure only when replacement of a front bumper extension sub-assembly LH is necessary.
|
Bolt |
|
Nut |
Remove the 2 nuts, 2 bolts and front bumper extension sub-assembly LH.
52102F
16.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY RH
Perform the following procedure only when replacement of a front bumper extension sub-assembly RH is necessary.
Use the same procedure as for the RH and LH sides.