Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

E404410E01
2.49,0.604 4.177,0.802 1.688,0.198 10 false from Auxiliary Battery 3.917,1.938 5.604,2.135 1.688,0.198 10 false FOG FR 3.802,3.417 5.802,4.063 2,0.646 10 false Instrument Panel Junction Block Assembly 0.906,1.844 1.406,2.052 0.5,0.208 10 false B11 0.896,2.01 2.583,2.208 1.688,0.198 10 false Fog Light Assembly LH 0.906,3.76 2.594,3.958 1.688,0.198 10 false B10 0.781,1.26 1.281,1.469 0.5,0.208 10 false 1 0.969,1.26 1.469,1.469 0.5,0.208 10 false E 2.198,1.25 2.698,1.458 0.5,0.208 10 false B 2.385,1.25 2.885,1.458 0.5,0.208 10 false 2 4.521,0.802 6.208,1 1.688,0.198 10 false FOG FR 3.75,1.604 4.25,1.813 0.5,0.208 10 false 2 4.521,1.229 5.021,1.438 0.5,0.208 10 false 5 4.531,1.615 5.031,1.823 0.5,0.208 10 false 1 3.75,1.25 4.25,1.458 0.5,0.208 10 false 3 3.313,2.729 3.813,2.938 0.5,0.208 10 false 32 3.313,2.927 3.813,3.135 0.5,0.208 10 false 4F 5.229,1.51 5.729,1.719 0.5,0.208 10 false 52 5.208,1.698 5.708,1.906 0.5,0.208 10 false 4A 4.625,2.917 6.313,3.115 1.688,0.198 10 false from TAIL Relay 3.875,3.073 5.563,3.271 1.688,0.198 10 false TAIL 6.042,1.708 6.542,1.917 0.5,0.208 10 false FFGO 5.875,1.594 6.375,1.802 0.5,0.208 10 false 7 5.521,4.323 6.021,4.531 0.5,0.208 10 false A 5.51,4.479 7.156,4.938 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 1.354,1.552 3.042,1.75 1.688,0.198 10 false Fog Light 2.188,3.125 2.688,3.333 0.5,0.208 10 false B 0.979,3.135 1.479,3.344 0.5,0.208 10 false E 0.802,3.146 1.302,3.354 0.5,0.208 10 false 1 2.375,3.135 2.875,3.344 0.5,0.208 10 false 2 1.333,3.438 3.021,3.635 1.688,0.198 10 false Fog Light 0.927,3.969 2.615,4.167 1.688,0.198 10 false Fog Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog light Relay OFF or ON Light control switch in TAIL position
Body Electrical > Main Body > Active Test
Tester Display
Front Fog Light Relay
50004 123 16
OK:

Front fog light relay operates (Front fog lights come on).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - BATTERY)
a.

Remove the FOG FR relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (FOG FR relay) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)
a.

Remove the FOG FR relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 (FOG FR relay) - Body ground Light control switch in TAIL or HEAD position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT FOG FR RELAY

NG

8.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
4.INSPECT FOG FR RELAY
a.

Remove the FOG FR relay.


b.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT LIGHT UNIT)

NG

REPLACE FOG FR RELAY

5.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT LIGHT UNIT)
a.

Remove the FOG FR relay.


b.

Disconnect the B11 fog light light unit LH connector.


c.

Disconnect the B10 fog light light unit RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (FOG FR relay) - B10-2 (B) Always Below 1 Ω
3 (FOG FR relay) - B11-2 (B) Always Below 1 Ω
3 (FOG FR relay) or B10-2 (B) - Body ground Always 10 kΩ or higher
3 (FOG FR relay) or B11-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the FOG FR relay.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FOG FR relay) - 4A-52 Always Below 1 Ω
1 (FOG FR relay) or 4A-52 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E361166C23
5.042,0.521 5.396,0.76 0.354,0.24 1.531,0.281 1.885,0.521 0.354,0.24 4.24,1.042 4.708,1.479 true 5.208,0.573 5.365,0.771 0.156,0.198 10 false A 1.625,0.323 1.844,0.542 0.219,0.219 10 false 4A 0.25,0.135 0.469,0.354 0.219,0.219 10 false *a 4.76,1.417 5.333,1.656 0.573,0.24 10 false FFGO
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-52 - A-7 (FFGO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the FOG FR relay.


b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FOG FR relay) - 4F-32 Always Below 1 Ω
2 (FOG FR relay) or 4F-32 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR