Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E412652E01
0.448,0.74 1.323,1.167 0.875,0.427 10 false from Auxiliary Battery 1.625,0.896 2.896,1.229 1.271,0.333 10 false DC/DC*1, ALT*2 4.448,1.385 4.802,1.615 0.354,0.229 10 false TAIL 5.135,1.25 5.49,1.479 0.354,0.229 10 false TAIL 5.917,0.635 6.344,0.865 0.427,0.229 10 false TRLY 3.719,3 5.323,3.396 1.604,0.396 10 false Instrument Panel Junction Block Assembly 5.448,3.625 7.135,4.625 1.688,1 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,3.448 5.823,3.677 0.354,0.229 10 false A 5.688,0.646 6.042,0.875 0.354,0.229 10 false 14 3.333,1.677 3.688,1.906 0.354,0.229 10 false 4F 3.323,1.49 3.677,1.719 0.354,0.229 10 false 32 3.313,2.448 3.667,2.677 0.354,0.229 10 false 4H 3.25,2.25 3.604,2.479 0.354,0.229 10 false 30*5 1.198,1.688 3,2.365 1.802,0.677 10 false to FOG FR Relay*3 3.313,0.74 3.667,0.969 0.354,0.229 10 false 4K 3.292,0.531 3.646,0.76 0.354,0.229 10 false 1*5 0.156,2.427 2.438,3.323 2.281,0.896 10 false to Taillights and License Plate Lights 0.313,3.01 2.073,3.26 1.76,0.25 10 false *1: for HV Model 0.313,3.313 2.073,3.563 1.76,0.25 10 false *2: for Gasoline Model 0.313,3.615 2.073,3.865 1.76,0.25 10 false *3: w/ Front Fog Light 2.833,2.25 3.188,2.479 0.354,0.229 10 false 30*4 2.865,2.448 3.219,2.677 0.354,0.229 10 false 4N 0.313,3.938 3.135,4.24 2.823,0.302 10 false *4: for LHD, Manual Transaxle 0.313,4.25 3.135,4.552 2.823,0.302 10 false *5: except LHD, Manual Transaxle 2.854,0.75 3.208,0.979 0.354,0.229 10 false 4M 2.854,0.542 3.208,0.771 0.354,0.229 10 false 1*4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.

Disconnect the 4M*1 or 4K*2 instrument panel junction block assembly connector.

*1: for LHD, Manual Transaxle

*2: except LHD, Manual Transaxle



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle:
Tester Connection Switch Condition Specified Condition
4M-1 - Body ground Ignition switch off 11 to 14 V

except LHD, Manual Transaxle:
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367362C11
1.479,0.344 1.844,0.552 0.365,0.208 4.875,0.729 5.25,0.948 0.375,0.219 2.323,2.156 2.688,2.365 0.365,0.208 5.083,1.958 5.448,2.167 0.365,0.208 2.323,1.865 2.688,2.073 0.365,0.208 5.094,2.229 5.458,2.438 0.365,0.208 4.677,1.542 4.844,1.208 false 0.302,0.177 0.615,0.375 0.313,0.198 10 false *a 1.573,0.375 1.885,0.573 0.313,0.198 10 false 4F 2.417,2.188 2.729,2.385 0.313,0.198 10 false 4H 5.021,0.75 5.333,0.948 0.313,0.198 10 false A 4.51,1.563 5.01,1.802 0.5,0.24 10 false TRLY 5.188,1.99 5.5,2.188 0.313,0.198 10 false 4M 2.427,1.896 2.74,2.094 0.313,0.198 10 false 4N 2.75,1.896 3.063,2.094 0.313,0.198 10 false *1 2.75,2.177 3.063,2.375 0.313,0.198 10 false *2 5.188,2.26 5.5,2.458 0.313,0.198 10 false 4K 5.531,1.958 5.844,2.156 0.313,0.198 10 false *1 5.542,2.25 5.854,2.448 0.313,0.198 10 false *2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -
*1 for LHD, Manual Transaxle *2 except LHD, Manual Transaxle



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Connect a positive (+) lead from the auxiliary battery to terminal 4M-1*1 or 4K-1*2.

*1: for LHD, Manual Transaxle

*2: except LHD, Manual Transaxle



d.

Connect a negative (-) lead from the auxiliary battery to terminal A-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4F-32 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between terminals 4M-1 - A-14 (TRLY) 11 to 14 V
4N-30 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between terminals 4M-1 - A-14 (TRLY) 11 to 14 V

except LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4F-32 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between terminals 4K-1 - A-14 (TRLY) 11 to 14 V
4H-30 - Auxiliary battery negative (-) terminal Auxiliary battery voltage is applied between terminals 4K-1 - A-14 (TRLY) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG