Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370843 AIR CONDITIONING SYSTEM(for Gasoline Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model)  B1451  Compressor Solenoid Circuit  


DESCRIPTION

The compressor with pulley assembly receives refrigerant compression demand signals from the air conditioning amplifier assembly.

Based on this signal, the compressor with pulley assembly changes the amount of compressor output.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor with pulley assembly

·

Harness or connector

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E370998E18
0.583,2.271 4.01,2.531 3.427,0.26 10 false Compressor with Pulley Assembly 0.583,2.115 0.979,2.323 0.396,0.208 10 false C44 1.708,0.667 2.104,0.875 0.396,0.208 10 false SOL+ 1.74,1.469 2.135,1.677 0.396,0.208 10 false SOL- 2.177,0.667 2.573,0.875 0.396,0.208 10 false 2 2.167,1.469 2.563,1.677 0.396,0.208 10 false 1 4.927,0.688 5.323,0.896 0.396,0.208 10 false 18 5.177,0.688 5.573,0.896 0.396,0.208 10 false SOL+ 5.865,0.792 6.26,1 0.396,0.208 10 false IC 4.688,2.104 5.083,2.313 0.396,0.208 10 false G46 4.688,2.26 7,2.573 2.313,0.313 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
E369146C15
1.458,0.323 1.958,0.583 0.5,0.26 2.417,1.75 2.083,1.75 2.083,1.75 1.896,1.313 true 1.583,0.375 2.042,0.573 0.458,0.198 10 false C44 3.042,3.406 3.385,3.594 0.344,0.188 10 false GND 2.5,1.656 3.063,1.865 0.563,0.208 10 false SOL+ 0.115,0.104 0.49,0.344 0.375,0.24 12 false *a
*a Front view of wire harness connector
(to Compressor with Pulley Assembly)


a.

Disconnect the compressor with pulley assembly connector.


b.

Connect an oscilloscope to terminal 2 (SOL+) and body ground and check the waveform.

Item Content
Terminal No. C44-2 (SOL+) - Body ground
Tool Setting 5 V/DIV., 500 μs./DIV.
Condition
·

Engine running

·

Blower switch: LO

·

A/C switch: On



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT COMPRESSOR WITH PULLEY ASSEMBLY
2.INSPECT COMPRESSOR WITH PULLEY ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the C44 compressor with pulley assembly connector.


b.

Disconnect the G46 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C44-2 (SOL+) - G46-18 (SOL+) Always Below 1 Ω
C44-2 (SOL+) or G46-18 (SOL+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR