Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for RHD with Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0378194 BRAKE MASTER CYLINDER(for RHD with Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for RHD with Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE MASTER CYLINDER O-RING

a.

Install a new brake master cylinder O-ring to the brake master cylinder sub-assembly.


Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.


a.

for Manual Transaxle:

i.

When installing a new brake master cylinder reservoir assembly or a new brake master cylinder sub-assembly, remove the protector from the brake master cylinder reservoir assembly.



b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




c.
C409037C01
2.906,3.135 2.813,3.135 2.813,3.135 2.719,2.719 false 1.802,3.021 2.115,3.177 0.313,0.156 10 false *a 2.958,3.063 3.271,3.219 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click here

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




d.
C407849

Engage the clamp and connect the connector to the brake master cylinder reservoir assembly.


Hide 31434E 3.CONNECT NO. 1 CLUTCH RESERVOIR HOSE (for Manual Transaxle)

a.
C409038C01
1.365,1.792 1.531,1.792 1.531,1.792 1.781,1.208 true 1.177,1.688 1.375,1.875 0.198,0.188 10 true *a
*a Paint Mark


Connect the No. 1 clutch reservoir hose to the brake master cylinder reservoir assembly and slide the clip to secure it.

NOTICE:
·

Make sure to position the paint mark of the No. 1 clutch reservoir hose so that it faces the right side of the vehicle.

·

Make sure that the tabs of the clip are facing the right side of the vehicle.




Hide 55704B 4.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 5.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY