CLEARANCE WARNING ECU ASSEMBLY
Disconnect the H4 clearance warning ECU assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| H4-1 (IG) - H4-28 (E) | B - W-B | IG power source signal | Engine switch off | Below 1 V |
| Engine switch on (IG) | 11 to 14 V*1
10.5 to 16 V*2 |
|||
| H4-28 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H4 clearance warning ECU assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H4-2 (BOF) - H4-28 (E) | R - W-B | Power source for front sensor circuit | ·
Engine switch on (IG) ·
Parking support brake system on |
11 to 14 V |
| H4-3 (SOF) - H4-28 (E) | L - W-B | Front sensor communication signal (Front clearance sonar sensor) | ·
Engine switch on (IG) ·
Parking support brake system on ·
Shift lever in any position other than P ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Pulse generation
(Refer to waveform 1) |
| H4-4 (E5) - H4-28 (E) | W - W-B | Ground for front clearance sonar | Always | Below 1 Ω |
| H4-9 (CBZ) - H4-8 (EF) | LG - L | No. 1 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| H4-19 (BOR) - H4-28 (E) | LG - W-B | Power source for rear sensor circuit | ·
Engine switch on (IG) ·
Parking support brake system on |
11 to 14 V |
| H4-20 (SOR) - H4-28 (E) | SB - W-B | Rear sensor communication signal (Rear clearance sonar sensor) | ·
Engine switch on (IG) ·
Parking support brake system on ·
Shift lever in R |
Pulse generation
(Refer to waveform 3) |
| H4-21 (E1) - H4-28 (E) | GR - W-B | Ground for rear clearance sonar | Always | Below 1 Ω |
| H4-25 (BBZ) - H4-26 (ER) | LG - L | No. 2 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | H4-3 (SOF) - H4-28 (E) |
| Measurement setting | 5 V/DIV., 1 ms./DIV. |
| Condition | ·
Engine switch on (IG) ·
Parking support brake system on ·
Shift lever in any position other than P ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | H4-9 (CBZ) - H4-8 (EF)
H4-25 (BBZ) - H4-26 (ER) |
| Measurement setting | 2 V/DIV., 500 μs./DIV. |
| Condition | Buzzer sounding |
The amplitude of the waveform changes according to the set volume.
Using an oscilloscope, check waveform 3.
Waveform 3 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | H4-20 (SOR) - H4-28 (E) |
| Measurement setting | 5 V/DIV., 1 ms./DIV. |
| Condition | ·
Engine switch on (IG) ·
Parking support brake system on ·
Shift lever in R |
ECM
for A25A-FKS:
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
BLIND SPOT MONITOR SENSOR RH (A) (w/ Blind Spot Monitor System)
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
BLIND SPOT MONITOR SENSOR LH (B) (w/ Blind Spot Monitor System)
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU