Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0378280 PARKING SUPPORT BRAKE SYSTEM(for Gasoline Model) C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM(for Gasoline Model)  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 100 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (A)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor LH (B)


U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 100 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor LH (B)

·

Blind spot monitor sensor LH (B) ground circuit

·

Blind spot monitor sensor RH (A)



WIRING DIAGRAM

E407527E03
4.333,4.531 5.729,5.167 1.396,0.635 10 false No. 100 CAN Junction Connector 4.333,4.344 4.948,4.542 0.615,0.198 10 false M30 4.198,3.438 4.458,3.677 0.26,0.24 10 false 5 4.135,3.802 4.396,4.042 0.26,0.24 10 false 16 3.781,3.438 4.042,3.677 0.26,0.24 10 false 37 3.771,3.802 4.031,4.042 0.26,0.24 10 false 38 3.313,3.563 3.927,3.76 0.615,0.198 10 false CANH 3.344,3.906 3.958,4.104 0.615,0.198 10 false CANL 2.698,4.417 3.927,4.979 1.229,0.563 10 false Clearance Warning ECU Assembly 2.688,4.25 3.302,4.448 0.615,0.198 10 false H4 4.177,0.833 4.438,1.073 0.26,0.24 10 false 7 4.146,1.458 4.406,1.698 0.26,0.24 10 false 18 5.552,0.854 5.823,1.073 0.271,0.219 10 false 1 5.563,1.469 5.833,1.688 0.271,0.219 10 false 6 3.292,0.833 3.906,1.031 0.615,0.198 10 false CA2P 5.75,0.854 6.365,1.052 0.615,0.198 10 false CA2P 5.75,1.708 6.365,1.906 0.615,0.198 10 false CA2N 3.281,1.708 3.896,1.906 0.615,0.198 10 false CA2N 3.76,0.854 4.031,1.073 0.271,0.219 10 false 1 3.781,1.479 4.052,1.698 0.271,0.219 10 false 6 2.583,1.021 2.854,1.24 0.271,0.219 10 false 5 2.521,1.708 2.792,1.927 0.271,0.219 10 false 10 2.771,1.135 3.385,1.333 0.615,0.198 10 false BLB 2.75,1.823 3.365,2.021 0.615,0.198 10 false BLGD 6.281,1.854 6.896,2.052 0.615,0.198 10 false BRGD 6.385,1.125 7,1.323 0.615,0.198 10 false BRB 6.802,0.99 7.073,1.208 0.271,0.219 10 false 5 6.771,1.729 7.042,1.948 0.271,0.219 10 false 10 2.792,2.573 3.969,3.188 1.177,0.615 10 false Blind Spot Monitor Sensor LH (B) 2.802,2.354 3.417,2.552 0.615,0.198 10 false Q1 5.688,2.375 6.302,2.573 0.615,0.198 10 false Q13 5.167,1.479 5.427,1.719 0.26,0.24 10 false 17 5.198,0.844 5.458,1.083 0.26,0.24 10 false 6 1.26,0.531 2.271,0.802 1.01,0.271 10 false ECU-IG1 NO.4 0.146,0.396 1.073,1.021 0.927,0.625 10 false from IG1 NO.1 Relay 5.667,2.552 6.844,3.229 1.177,0.677 10 false Blind Spot Monitor Sensor RH (A) 2.042,1.031 2.313,1.25 0.271,0.219 10 false *2 2.031,0.281 2.302,0.5 0.271,0.219 10 false *1 0.031,1.125 1.146,1.823 1.115,0.698 10 false from Engine Stop and Start ECU 0.042,5.042 2.344,5.406 2.302,0.365 10 false *1: w/o Stop and Start System 0.042,5.385 2.344,5.75 2.302,0.365 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438

b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Clear DTCs
50002 438

c.

Recheck for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 only is output A
DTC U117887 only is output B
DTC U117787 and U117887 are output C



A

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)

C

4.CHECK CAN BUS MAIN WIRE
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)
a.
E393028C54
1.5,0.302 1.958,0.552 0.458,0.25 2.583,1.865 2.333,1.865 2.333,1.865 2,1.365 true 2.552,0.635 2.302,0.635 2.302,0.635 2.01,1.167 true 1.604,0.365 1.958,0.573 0.354,0.208 10 false Q13 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.667,1.781 3.167,1.979 0.5,0.198 10 false BRGD 2.635,0.552 3.135,0.75 0.5,0.198 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Q13-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V*1
10.5 to 16 V*2
Q13-5 (BRB) - Body ground Engine switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)
a.
E393028C53
1.5,0.302 1.958,0.552 0.458,0.25 2.573,1.865 2.323,1.865 2.323,1.865 1.99,1.365 true 2.625,0.604 2.375,0.604 2.375,0.604 2.01,1.156 true 1.604,0.365 1.958,0.573 0.354,0.208 10 false Q1 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.656,1.792 3.156,1.99 0.5,0.198 10 false BLGD 2.74,0.51 3.24,0.708 0.5,0.198 10 false BLB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-10 (BLGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Q1-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V*1
10.5 to 16 V*2
Q1-5 (BLB) - Body ground Engine switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

4.CHECK CAN BUS MAIN WIRE
a.
E395856C11
1.49,2.792 1.938,3.031 0.448,0.24 0.24,1.448 0.635,1.708 0.396,0.26 1.073,2.948 1.26,2.948 1.26,2.948 1.604,3.417 true 2.333,3.917 2.49,4.302 2.49,4.302 2.635,4.302 true 1.833,1.854 2.365,2.583 2.365,2.583 2.51,2.583 true 1.844,1.604 2.573,0.771 2.573,0.771 2.719,0.771 true 0.24,2.708 0.552,2.865 0.313,0.156 10 false *b 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.531,2.833 1.885,3.031 0.354,0.198 10 false G114 0.292,1.49 0.698,1.688 0.406,0.198 10 false M30 2.781,0.708 3.271,0.906 0.49,0.198 10 false CANH 2.594,2.5 3.177,2.708 0.583,0.208 10 false CANL 2.698,4.208 3.281,4.417 0.583,0.208 10 false BAT 0.813,2.854 1.125,3.063 0.313,0.208 10 false CG
*a Component with harness connected
(No. 100 CAN Junction Connector)
*b Front view of DLC3


Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M30-5 (CANH) - M30-16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M30-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M30-16 (CANL) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M30-5 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M30-16 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

5.CHECK FOR DTC

B

6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 100 JUNCTION CONNECTOR)

C

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 100 JUNCTION CONNECTOR)

D

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 100 JUNCTION CONNECTOR)
5.CHECK FOR DTC
a.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Clear DTCs
50002 438

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are not output A
DTC U117787 and U117887 are output B



A

B

6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 100 JUNCTION CONNECTOR)
a.

Disconnect the No. 100 CAN junction connector.

C382852C19
1.052,1.24 1.458,1.49 0.406,0.25 3.146,0.417 3.396,0.417 3.396,0.417 3.594,1.396 true 3.115,2.344 3.365,2.344 3.365,2.344 3.552,1.729 true 3.333,0.177 3.583,0.177 3.583,0.177 3.771,1.427 true 3.271,2.656 3.521,2.656 3.521,2.656 3.771,1.708 true 2.948,2.104 3.198,2.104 3.198,2.104 3.406,1.708 true 2.792,0.667 3.042,0.667 3.042,0.667 3.375,1.406 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.104,1.292 1.604,1.531 0.5,0.24 10 false M30 2.583,0.323 3.25,0.563 0.667,0.24 10 false CANH*c 2.396,2.031 3.063,2.271 0.667,0.24 10 false CANL*b 2.25,0.583 2.917,0.823 0.667,0.24 10 false CANH*b 2.74,2.552 3.406,2.792 0.667,0.24 10 false CANL*d 2.552,2.25 3.219,2.49 0.667,0.24 10 false CANL*c 2.771,0.094 3.438,0.333 0.667,0.24 10 false CANH*d
*a Front view of wire harness connector
(to No. 100 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire *d to Blind Spot Monitor Sensor LH (B) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-5 (CANH) - M30-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-6 (CANH) - M30-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M30-7 (CANH) - M30-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 100 CAN JUNCTION CONNECTOR

B

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

C

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

D

9.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.
E393028C55
1.51,0.302 1.969,0.552 0.458,0.25 0.854,1.854 1.104,1.854 1.104,1.854 1.333,1.365 true 0.781,0.656 1.031,0.656 1.031,0.656 1.344,1.146 true 1.635,0.365 1.99,0.573 0.354,0.208 10 false Q1 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-1 (CA2P) - Q1-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 100 CAN JUNCTION CONNECTOR)

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.
E393028C56
1.51,0.302 1.969,0.552 0.458,0.25 0.854,1.854 1.104,1.854 1.104,1.854 1.333,1.365 true 0.781,0.656 1.031,0.656 1.031,0.656 1.344,1.146 true 1.615,0.365 1.969,0.573 0.354,0.208 10 false Q13 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-1 (CA2P) - Q13-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 100 CAN JUNCTION CONNECTOR)

9.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.
C369149C29
1.5,0.5 1.917,0.75 0.417,0.25 2.25,2.417 2.5,2.417 2.5,2.417 2.74,1.823 true 2.406,2.719 2.656,2.719 2.656,2.719 2.854,1.823 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.604,0.552 1.917,0.75 0.313,0.198 10 false H4 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-37 (CANH) - H4-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 100 CAN JUNCTION CONNECTOR)

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 100 JUNCTION CONNECTOR)
a.

Disconnect the No. 100 CAN junction connector.

C382852C19
1.052,1.24 1.458,1.49 0.406,0.25 3.146,0.417 3.396,0.417 3.396,0.417 3.594,1.396 true 3.115,2.344 3.365,2.344 3.365,2.344 3.552,1.729 true 3.333,0.177 3.583,0.177 3.583,0.177 3.771,1.427 true 3.271,2.656 3.521,2.656 3.521,2.656 3.771,1.708 true 2.948,2.104 3.198,2.104 3.198,2.104 3.406,1.708 true 2.792,0.667 3.042,0.667 3.042,0.667 3.375,1.406 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.104,1.292 1.604,1.531 0.5,0.24 10 false M30 2.583,0.323 3.25,0.563 0.667,0.24 10 false CANH*c 2.396,2.031 3.063,2.271 0.667,0.24 10 false CANL*b 2.25,0.583 2.917,0.823 0.667,0.24 10 false CANH*b 2.74,2.552 3.406,2.792 0.667,0.24 10 false CANL*d 2.552,2.25 3.219,2.49 0.667,0.24 10 false CANL*c 2.771,0.094 3.438,0.333 0.667,0.24 10 false CANH*d
*a Front view of wire harness connector
(to No. 100 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire *d to Blind Spot Monitor Sensor LH (B) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-5 (CANH) - M30-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-6 (CANH) - M30-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
M30-7 (CANH) - M30-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 100 CAN JUNCTION CONNECTOR

B

11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

12.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

13.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.
E393028C55
1.51,0.302 1.969,0.552 0.458,0.25 0.854,1.854 1.104,1.854 1.104,1.854 1.333,1.365 true 0.781,0.656 1.031,0.656 1.031,0.656 1.344,1.146 true 1.635,0.365 1.99,0.573 0.354,0.208 10 false Q1 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-1 (CA2P) - Q1-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 100 JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.
E393028C56
1.51,0.302 1.969,0.552 0.458,0.25 0.854,1.854 1.104,1.854 1.104,1.854 1.333,1.365 true 0.781,0.656 1.031,0.656 1.031,0.656 1.344,1.146 true 1.615,0.365 1.969,0.573 0.354,0.208 10 false Q13 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-1 (CA2P) - Q13-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 100 JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
C369149C29
1.5,0.5 1.917,0.75 0.417,0.25 2.25,2.417 2.5,2.417 2.5,2.417 2.74,1.823 true 2.406,2.719 2.656,2.719 2.656,2.719 2.854,1.823 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.604,0.552 1.917,0.75 0.313,0.198 10 false H4 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-37 (CANH) - H4-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 100 JUNCTION CONNECTOR)

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 100 JUNCTION CONNECTOR)
a.

Disconnect the No. 100 junction connector.

E407528C01
0.427,1.333 0.875,1.583 0.448,0.25 4.052,1.25 4.5,1.5 0.448,0.25 1.458,0.573 1.625,0.573 1.625,0.573 2.156,1.385 true 1.542,2.25 1.708,2.25 1.708,2.25 2.167,1.708 true 1.802,0.323 1.969,0.323 1.969,0.323 2.354,1.375 true 1.833,2.563 2,2.563 2,2.563 2.354,1.719 true 3.125,0.49 2.958,0.49 2.958,0.49 2.563,1.365 true 3.063,2.396 2.896,2.396 2.896,2.396 2.531,1.719 true 5.635,2.302 5.802,2.302 5.802,2.302 6.146,1.625 true 6,0.573 5.833,0.573 5.833,0.573 5.552,1.177 true 0.302,0.479 0.615,0.677 0.313,0.198 10 false *a 4.323,0.563 4.635,0.76 0.313,0.198 10 false *b 0.885,0.469 1.5,0.677 0.615,0.208 10 false CANH*c 0.99,2.167 1.604,2.375 0.615,0.208 10 false CANL*c 1.229,0.219 1.844,0.427 0.615,0.208 10 false CANH*d 1.292,2.469 1.906,2.677 0.615,0.208 10 false CANL*d 3.208,0.427 3.823,0.635 0.615,0.208 10 false CANH*e 3.156,2.323 3.771,2.531 0.615,0.208 10 false CANL*e 0.51,1.375 0.958,1.635 0.448,0.26 10 false M30 4.115,1.302 4.563,1.563 0.448,0.26 10 false G114 5.323,2.24 5.938,2.448 0.615,0.208 10 false BAT 6.063,0.49 6.677,0.698 0.615,0.208 10 false CG
*a Front view of wire harness connector
(to No. 100 CAN Junction Connector)
*b Front view of DLC3
*c to Clearance Warning ECU Assembly CAN Wire *d to Blind Spot Monitor Sensor RH (A) CAN Main Wire
*e to Blind Spot Monitor Sensor LH (B) CAN Main Wire - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-16 (CANL) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-5 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M30-16 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M30-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-17 (CANL) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-6 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M30-17 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M30-7 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-18 (CANL) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M30-7 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M30-18 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 100 CAN JUNCTION CONNECTOR

B

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

17.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.
E395848C12
1.51,1.656 1.906,1.948 0.396,0.292 1.458,0.125 1.906,0.438 0.448,0.313 0.76,0.646 0.948,0.646 0.948,0.646 1.396,0.958 true 0.76,1.375 0.948,1.375 0.948,1.375 1.375,1.115 true 1.167,1.885 1.333,1.885 1.333,1.885 1.604,2.271 true 2.26,2.74 2.448,3.042 2.448,3.042 2.563,3.042 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.552,1.719 1.979,1.948 0.427,0.229 10 false G114 1.573,0.188 1.885,0.385 0.313,0.198 10 false Q1 0.344,0.583 0.958,0.781 0.615,0.198 10 false CA2P 0.344,1.313 0.958,1.51 0.615,0.198 10 false CA2N 2.656,2.969 3.271,3.167 0.615,0.198 10 false BAT 0.875,1.813 1.49,2.01 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))
*b Front view of DLC3


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-1 (CA2P) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q1-6 (CA2N) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q1-1 (CA2P) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q1-6 (CA2N) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 100 JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.
E395848C13
1.51,1.656 1.906,1.948 0.396,0.292 1.458,0.125 1.906,0.438 0.448,0.313 0.76,0.646 0.948,0.646 0.948,0.646 1.396,0.958 true 0.76,1.375 0.948,1.375 0.948,1.375 1.375,1.115 true 1.167,1.885 1.333,1.885 1.333,1.885 1.604,2.271 true 2.26,2.74 2.448,3.042 2.448,3.042 2.563,3.042 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.552,1.719 1.979,1.948 0.427,0.229 10 false G114 1.552,0.208 1.865,0.406 0.313,0.198 10 false Q13 0.344,0.583 0.958,0.781 0.615,0.198 10 false CA2P 0.344,1.313 0.958,1.51 0.615,0.198 10 false CA2N 2.656,2.969 3.271,3.167 0.615,0.198 10 false BAT 0.875,1.813 1.49,2.01 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))
*b Front view of DLC3


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-1 (CA2P) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-6 (CA2N) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-1 (CA2P) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q13-6 (CA2N) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 100 JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
E407529C01
1.458,0.302 1.823,0.563 0.365,0.26 1.469,1.74 1.906,2.01 0.438,0.271 2.958,1.865 2.76,1.865 2.76,1.865 2.594,1.271 true 2.604,3.25 2.406,3.25 2.406,3.25 2.25,2.833 true 1.615,2.375 1.313,1.979 1.313,1.979 1.094,1.979 true 2.938,2.219 2.74,2.219 2.74,2.219 2.49,1.281 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.229,1.938 0.542,2.135 0.313,0.198 10 false *b 1.552,0.354 1.865,0.51 0.313,0.156 10 false H4 1.531,1.792 1.99,1.99 0.458,0.198 10 false G114 2.99,1.771 3.396,2 0.406,0.229 10 false CANL 2.979,2.156 3.385,2.385 0.406,0.229 10 false CANH 2.635,3.167 3.042,3.396 0.406,0.229 10 false BAT 0.802,1.917 1.208,2.146 0.406,0.229 10 false CG
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3


Reconnect the M30 No. 100 CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-37 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
H4-38 (CANL) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
H4-37 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H4-38 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 100 JUNCTION CONNECTOR)