Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A4  Open or Short Circuit in Release Switch Circuit  C13AC  Release Switch Circuit Comparison  


DESCRIPTION

When the electric parking brake switch (integration control and panel assembly) is pushed to the release side, a release request signal is output to the parking brake ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A4 Open or Short Circuit in Release Switch Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pushed to release side with power switch off.

2.

Terminal REL1 voltage is less than 1.4 V* or more than 9.0 V*; or terminal REL2 voltage is less than 1.4 V* or more than 9.0 V*.

3.

Problem occurs for approximately 1 second.


HINT:

*: This value is based on the assumption that the BECU terminal voltage is 11 V.

The threshold changes according to the BECU terminal voltage.

For details, refer to "Threshold Changes According to BECU Terminal Voltage".


·

Electric parking brake switch (integration control and panel assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.
C13AC Release Switch Circuit Comparison Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pulled to release side with power switch off.

2.

ON/OFF judgment of release switch 1 and release switch 2 does not match for approximately 1 second.


·

Electric parking brake switch (integration control and panel assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13A4 (Pattern1, Pattern2, Pattern3, Pattern4)
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to release side with power switch off ○ ○ - -
Power switch on (IG) - - ○ ○
Malfunction Status REL1 terminal voltage is below 1.4 V (*) ○ - ○ -
REL1 terminal voltage is above 9.0 V (*) - ○ - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip 1 trip 1 trip

DTC Detection Condition Combination Table: C13A4 (Pattern 5, Pattern 6, Pattern 7, Pattern 8)
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to release side with power switch off ○ ○ - -
Power switch on (IG) - - ○ ○
Malfunction Status REL2 terminal voltage is below 1.4 V (*) ○ - ○ -
REL2 terminal voltage is above 9.0 V (*) - ○ - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip 1 trip 1 trip

HINT:
·

If the conditions match either of these patterns, a DTC will be output.

·

*: This value is based on the assumption that the BECU terminal voltage is 11 V.

The threshold changes according to the BECU terminal voltage.

For details, refer to "Threshold Changes According to BECU Terminal Voltage".



Threshold Changes According to BECU Terminal Voltage
C377928C05
0.427,0.542 0.74,0.74 0.313,0.198 10 false *c 0.427,0.813 0.74,1.01 0.313,0.198 10 false *d 0.656,1.729 0.969,1.927 0.313,0.198 10 false *b 2.219,3.177 2.531,3.375 0.313,0.198 10 false *a
*a BECU Terminal Voltage (V)
*b REL1 or REL2 Terminal Voltage (V)
*c Normal Range
*d DTC Detection Range


DTC Detection Condition Combination Table: C13AC
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to release side with power switch off ○ -
Power switch on (IG) - ○
Malfunction Status Release 1 switch and release 2 switch ON/OFF evaluations do not match ○ ○
Detection Time Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When the electric parking brake switch (integration control and panel assembly) is pushed and held for 1 second or more without being pushed fully to the release side, one of the 2 linked contacts may turn on while the other one turns off causing this DTC to be stored (system is not malfunctioning).

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.

Remove the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))
a.

Disconnect the G32 electric parking brake switch (integration control and panel assembly) connector.


b.

Disconnect the M35 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-19 (REL1) - G32-22 (RLS1) Always Below 5 Ω
M35-16 (REL2) - G32-23 (RLS2) Always Below 5 Ω
M35-19 (REL1) or G32-22 (RLS1) - Body ground Always 10 kΩ or higher
M35-16 (REL2) or G32-23 (RLS2) - Body ground Always 10 kΩ or higher
G32-15 (E) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Perform a release operation with the electric parking brake switch (integration control and panel assembly).

HINT:

When the electric parking brake switch (integration control and panel assembly) is pushed and held for 1 second or more without being pushed fully to the release side, one of the 2 linked contacts may turn on while the other one turns off causing this DTC to be stored (system is not malfunctioning).



e.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Proceed to
DTC is output
DTC is not output



DTC is output

REPLACE PARKING BRAKE ECU ASSEMBLY

DTC is not output