Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1231  Steering Angle Sensor Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives steering sensor signals via CAN communication. When a malfunction occurs in the communication line with the steering sensor, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1231 Steering Angle Sensor Circuit 701
702
703
·

INF Code: 701

-

While steering sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction).


·

INF Code: 702

-

While steering sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction).


·

INF Code: 703

-

While steering sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction).



Steering sensor internal malfunction -

WIRING DIAGRAM

C270521E99
0.073,4.031 0.396,4.333 0.323,0.302 10 false G68 0.885,3.313 1.667,3.615 0.781,0.302 10 false ESS 0.792,0.667 1.583,0.938 0.792,0.271 10 false CANL 0.771,1.26 1.688,1.51 0.917,0.25 10 false CANH 0.896,1.969 1.49,2.24 0.594,0.271 10 false BAT 0.948,2.635 1.344,2.948 0.396,0.313 10 false IG1 1.313,0.49 1.51,0.677 0.198,0.188 10 false 8 1.323,1.094 1.781,1.375 0.458,0.281 10 false 3 1.313,1.813 1.76,2.125 0.448,0.313 10 false 4 1.281,2.51 1.604,2.792 0.323,0.281 10 false 9 1.313,3.167 1.656,3.521 0.344,0.354 10 false 6 2.052,2.115 3.083,2.354 1.031,0.24 10 false ECU-DCC NO.1 2.021,2.792 3.094,3.135 1.073,0.344 10 false ECU-IG1 NO.2 3.896,1.938 5.865,2.375 1.969,0.438 10 false from Auxiliary Battery 3.896,2.625 5.573,3 1.677,0.375 10 false from IG Circuit 5.781,1.083 6.219,1.417 0.438,0.333 10 false 37 4.75,4.042 5.292,4.313 0.542,0.271 10 false A42 6.031,0.656 6.688,0.948 0.656,0.292 10 false CA1L 6.031,1.271 6.708,1.604 0.677,0.333 10 false CA1H 5.781,0.49 6.135,0.781 0.354,0.292 10 false 38 5.083,4.042 7.156,4.479 2.073,0.438 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.427,4.031 1.5,4.26 1.073,0.229 10 false Steering Sensor 2.938,3.552 5.188,4 2.25,0.448 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

When U0126 is output together with C1231, inspect and repair the trouble areas indicated by U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>U0073

·

When a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the power switch off.


c.

Turn the power switch on (IG) again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM


d.

Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1231 is output. A
CAN communication system DTCs are output. B
Speed sensor and/or yaw rate and acceleration sensor DTCs are output. C
DTC C1231 is not output. D


HINT:
·

When CAN communication system DTCs are output, repair the CAN communication system before repairing each corresponding sensor.

·

If there is a malfunction in a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output even though the steering sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering sensor.





A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

C

D

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C374262C61
0.229,0.771 0.615,1.01 0.385,0.24 2,1.99 2.604,1.635 true 1.99,2.365 2.552,2.854 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.302,0.813 0.76,1.01 0.458,0.198 10 false G68 2.667,1.552 3.125,1.75 0.458,0.198 10 false BAT 2.646,2.833 3.104,3.031 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Turn the power switch off.


b.

Remove the steering wheel and column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the G68 steering sensor connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G68-4 (BAT) - Body ground Always 11 to 14 V
G68-9 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C374262C62
0.229,0.771 0.615,1.01 0.385,0.24 0.688,2.75 1.292,2.396 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.302,0.823 0.76,1.021 0.458,0.198 10 false G68 0.417,2.719 0.875,2.917 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
G68-6 (ESS) - Body ground 1 minute after power switch off Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)