Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  U0073  Control Module Communication Bus OFF  U0110  Lost Communication with Drive Motor Control Module "A"  U0120  Lost Communication with Starter / Generator Control Module  U0123  Lost Communication with Yaw Rate Sensor Module  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0128  Lost Communication With EPB Module  U0151  Lost Communication With Restraints Control Module  U0293  Lost Communication With Hybrid Vehicle Control System  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives signals from the hybrid vehicle control ECU assembly, steering sensor, parking brake ECU assembly, certification ECU (smart key ECU assembly), inverter with converter assembly and yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
U0073 Control Module Communication Bus OFF 461
462
463
464
465
466
·

INF Code: 461

-

Either of the following is detected:

(1)

Yaw rate and acceleration sensor communication is disabled for 1 second or more.

(2)

Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.




·

INF Code: 462

-

Either of the following is detected:

(1)

Steering sensor communication is disabled for 1 second or more.

(2)

Steering sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.




·

INF Code: 463, 464

-

Bus off occurs once or more per 0.1 seconds 10 times repeatedly.



·

INF Code: 465, 466

-

Sending does not complete within 5 seconds after data is output from the skid control ECU (brake booster with master cylinder assembly).



·

INF Code: 461

-

CAN communication line (V bus)

-

Yaw rate and acceleration sensor (Airbag sensor assembly)

-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 462

-

CAN communication line (V bus)

-

Steering sensor

-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 463, 464, 465, 466

-

CAN communication line

-

Skid control ECU (Brake booster with master cylinder assembly)



-
U0110 Lost Communication with Drive Motor Control Module "A" 1153
1154
·

INF Code: 1153

-

The IG2 terminal voltage is 9.5 V higher than and data cannot be received from the inverter with converter assembly for 2 seconds.



·

INF Code: 1154

-

The IG2 terminal voltage is 9.5 V higher than and data cannot be received from the inverter with converter assembly once or more per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line

·

Inverter with converter assembly

·

Skid control ECU (Brake booster with master cylinder assembly)


-
U0120 Lost Communication with Starter / Generator Control Module 471 Push start switch data is invalid for 3 seconds or more.
·

CAN communication line (V bus)

·

Certification ECU (Smart key ECU assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


-
U0123 Lost Communication with Yaw Rate Sensor Module 731
732
·

INF Code: 731

-

Yaw rate sensor communication is disabled for 1 second or more.



·

INF Code: 732

-

Yaw rate sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Yaw rate sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


-
U0124 Lost Communication with Lateral Acceleration Sensor Module 591
592
·

INF Code: 591

-

Acceleration sensor communication is disabled for 1 second or more.



·

INF Code: 592

-

Acceleration sensor communication is disabled once per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


-
U0126 Lost Communication with Steering Angle Sensor Module 741
742
·

INF Code: 741

-

Steering sensor communication is disabled for 1 second or more.



·

INF Code: 742

-

Steering sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.



·

CAN communication line (V bus)

·

Steering sensor

·

Skid control ECU (Brake booster with master cylinder assembly)


-
U0128 Lost Communication With EPB Module 425 With terminal IG1 voltage at 10 V or more, data cannot be received from the electric parking brake ECU for 1 second.
·

CAN communication line (V bus)

·

Parking brake ECU assembly

·

Skid control ECU (Brake booster with master cylinder assembly)


EPB: Electric Parking Brake System
U0151 Lost Communication With Restraints Control Module 450 The IG2 terminal voltage is 9.5 V higher than and data cannot be received from the airbag sensor assembly continuously for 5 seconds.
·

CAN communication system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Airbag sensor assembly


-
U0293 Lost Communication With Hybrid Vehicle Control System 411
412
413
Either of the following is detected:
1.

When terminal IG2 voltage is 9.5 V higher than, data from the hybrid vehicle control ECU assembly cannot be received for 2 seconds or more.

2.

When terminal IG2 voltage is 9.5 V higher than, data from the hybrid vehicle control ECU assembly cannot be received once or more within 5 seconds occur 10 times in succession.


·

CAN communication line (V bus)

·

Hybrid vehicle control ECU assembly

·

Skid control ECU (Brake booster with master cylinder assembly)


-

DTC Detection Conditions: U0073 INF Code: 461
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Yaw rate and acceleration sensor communication is disabled ○ -
Communication is disabled once or more per 5 seconds 10 times or more within 60 seconds - ○
Detection Time 1 second or more -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: U0073 INF Code: 462
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Steering sensor communication is disabled ○ -
Steering sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds - ○
Detection Time 1 second or more -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: U0293
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status When terminal IG2 voltage is 9.5 V higher than, data from the hybrid vehicle control ECU assembly cannot be received ○ -
When terminal IG2 voltage is 9.5 V higher than, data from the hybrid vehicle control ECU assembly cannot be received once or more within 5 seconds occur 10 times in succession - ○
Detection Time 2 seconds or more -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Open Yaw rate sensor open detection Error or Normal Normal: Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection Error or Normal Normal: Normal Error: Momentary interruption
Steering Open Steering sensor open detection Error or Normal Normal: Normal Error: Momentary interruption
HV Communication Open Hybrid vehicle communication open detection Error or Normal Normal: Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
Yaw Rate Open
Deceleration Open
Steering Open
HV Communication Open
50003 105 205,206,207,217
Result:
Result Proceed to
There is a constant open circuit. A
There are no momentary interruptions. B
There are momentary interruptions. C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.




A

2.CHECK IF EACH CONNECTOR IS SECURELY CONNECTED (ECU, SENSOR)

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH CONNECTOR IS SECURELY CONNECTED (ECU, SENSOR)
a.

Turn the power switch off.


b.

Check if each sensor and ECU connector is securely connected.

OK:

Each sensor and ECU connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECU CORRECTLY

3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Record the output DTCs (for the ABS, VSC, electronically controlled brake system and/or CAN communication system).

for the ABS, VSC and Electronically Controlled Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

for the CAN Communication System: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If CAN communication system DTCs and relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for the ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.



Result:
Result Proceed to
DTCs are not output. A
ABS, VSC and/or electronically controlled brake system DTCs are output. B
CAN communication system DTCs are output. C



A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the power switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruptions between the skid control ECU (brake booster with master cylinder assembly) and each sensor or ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch on (READY).


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM


f.

If ABS, VSC and/or electronically controlled brake system DTCs are output, record them.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs are not output. A
ABS, VSC and/or electronically controlled brake system DTCs are output. B
CAN communication system DTCs are output. C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for the ABS, VSC and/or electronically controlled brake system).




A

END

B

C