Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1252  Brake Booster Pump Motor on Time Abnormally Long  C1253  Pump Motor Relay  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1252 Brake Booster Pump Motor on Time Abnormally Long 311 The pump motor is operating continuously for 178 seconds or more. (When the relay is malfunctioning for 98 seconds or more.)
·

Short in motor circuit or motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction in brake actuator (Brake booster with master cylinder assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


-
C1253 Pump Motor Relay 321
322
323
324
325
326
327
328
329
·

INF Code: 321

-

With IG1 terminal voltage 9.5 V higher than, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request.


·

INF Code: 322

-

The motor drive monitor remains on for 2 seconds or more after a motor drive off request.


·

INF Code: 323

-

A skid control ECU (brake booster with master cylinder assembly) internal motor drive logical inconsistency continues for 2 seconds or more.


·

INF Code: 324

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relays 1 and 2.


·

INF Code: 325

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relays 1 and 3.


·

INF Code: 326

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relays 2 and 3.


·

INF Code: 327

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relay 1.


·

INF Code: 328

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relay 2.


·

INF Code: 329

-

An open circuit is detected in the skid control ECU (brake booster with master cylinder assembly) internal motor relay 3.



·

INF Code: 321, 324, 325, 326, 327, 328, 329

-

Open in motor circuit or motor monitor circuit

-

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 322

-

Short in motor circuit or motor monitor circuit

-

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 323

-

Skid control ECU (Brake booster with master cylinder assembly)



-

WIRING DIAGRAM

C407568E02
2.615,7.188 3.656,7.385 1.042,0.198 10 false Auxiliary Battery 4.365,7.708 4.823,7.906 0.458,0.198 10 false A42 4.417,7.906 6.438,8.313 2.021,0.406 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.063,8.271 2.281,8.698 2.219,0.427 10 false Brake Booster Pump Assembly 1.167,0.479 1.625,0.677 0.458,0.198 10 false BM1 1.563,0.469 1.719,0.667 0.156,0.198 10 false 2 4.646,0.469 5.26,0.667 0.615,0.198 10 false MRO1 4.25,0.49 4.563,0.688 0.313,0.198 10 false 29 1.146,1.323 1.604,1.521 0.458,0.198 10 false BM2 1.583,1.313 1.74,1.51 0.156,0.198 10 false 1 4.635,1.292 5.25,1.49 0.615,0.198 10 false MRO2 4.271,1.292 4.583,1.49 0.313,0.198 10 false 30 3.135,3.823 4.323,4.073 1.188,0.25 10 false ABS MTR NO. 1 4.646,3.51 5.26,3.708 0.615,0.198 10 false MRI1 4.365,3.51 4.521,3.708 0.156,0.198 10 false 1 3.063,4.677 4.25,4.906 1.188,0.229 10 false ABS MTR NO. 2 4.677,4.365 5.292,4.563 0.615,0.198 10 false MRI2 4.344,4.323 4.5,4.521 0.156,0.198 10 false 2 1.052,5.823 1.667,6.021 0.615,0.198 10 false GND1 1.604,5.771 1.76,5.969 0.156,0.198 10 false 4 2.552,5.531 3.167,5.729 0.615,0.198 10 false MAIN 4.604,5.146 5.063,5.344 0.458,0.198 10 false GND 4.323,4.969 4.635,5.167 0.313,0.198 10 false 28 4.635,5.531 5.25,5.729 0.615,0.198 10 false GND2 4.323,5.333 4.635,5.531 0.313,0.198 10 false 27 4.604,5.948 5.219,6.146 0.615,0.198 10 false GND3 4.323,5.802 4.635,6 0.313,0.198 10 false 26 4.635,6.438 5.25,6.635 0.615,0.198 10 false GND4 4.333,6.302 4.646,6.5 0.313,0.198 10 false 25 4.677,6.938 5.292,7.135 0.615,0.198 10 false GND5 4.333,6.792 4.646,6.99 0.313,0.198 10 false 24 4.625,7.385 5.24,7.583 0.615,0.198 10 false GND6 4.333,7.26 4.646,7.458 0.313,0.198 10 false 23 1,6.802 1.615,7 0.615,0.198 10 false GND2 1.583,6.677 1.74,6.875 0.156,0.198 10 false 3 0.083,8.021 0.542,8.219 0.458,0.198 10 false A49 4.875,2.448 5.448,2.979 0.573,0.531 10 false Motor Relay 6.365,2.063 6.719,2.427 0.354,0.365 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Motor Relay ABS motor relay Relay ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Motor Relay
50004 105 42

d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay ABS motor relay ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Data List
Tester Display
ECB Motor Relay
50003 105 63

e.

Check the operating condition of the ABS motor relay when operating it with the GTS.


Result:
Result Proceed to
ABS motor relay in the Data List turns ON/OFF using the Active Test. A
ABS motor relay in the Data List does not change using the Active Test. B



A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C406089C01
0.75,1.917 1,1.917 1,1.917 1.5,1.5 true 0.708,0.667 0.958,0.667 0.958,0.667 1.458,1.083 true 2.75,0.583 2.5,0.583 2.5,0.583 1.917,1.083 true 2.802,1.875 2.552,1.875 2.552,1.875 1.969,1.542 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 0.344,0.604 0.802,0.802 0.458,0.198 10 false BM1 0.344,1.844 0.802,2.042 0.458,0.198 10 false GND1 2.854,1.781 3.313,1.979 0.458,0.198 10 false GND2 2.833,0.521 3.292,0.719 0.458,0.198 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A49 brake booster pump assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always Below 10 Ω
1 (BM2) - 3 (GND2) Always Below 10 Ω
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C406090C01
1.5,0.167 1.917,0.417 0.417,0.25 0.75,1.917 1,1.917 1,1.917 1.5,1.5 true 2.802,1.875 2.552,1.875 2.552,1.875 1.969,1.542 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 0.354,1.833 0.813,2.031 0.458,0.198 10 false GND2 1.573,0.198 2.031,0.396 0.458,0.198 10 false A49 2.854,1.781 3.313,1.979 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Booster Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-4 (GND1) - Body ground Always Below 1 Ω
A49-3 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the A49 brake booster pump assembly connectors.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

e.

Depress the brake pedal 4 or 5 times to operate the pump motor.


f.

Wait for 30 seconds without depressing the brake pedal.


g.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

6.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
5.RECONFIRM DTC

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1252 and C1253 are not output. A
DTCs C1252 and/or C1253 are output. B



A

B

6.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SMC/SRC/SCC)
50004 105 89
HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).




b.

Perform the Active Test of the solenoid using the GTS.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

d.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
a.
C316493C43
0.208,0.729 0.594,0.99 0.385,0.26 0.813,1.823 0.448,2.719 true 1.177,1.823 1.354,2.729 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.281,0.781 0.74,0.979 0.458,0.198 10 false A42 0.271,2.823 0.729,3.021 0.458,0.198 10 false MRI1 1.281,2.823 1.74,3.021 0.458,0.198 10 false MRI2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (MRI1) - Body ground Always 11 to 14 V
A42-2 (MRI2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A49 brake booster pump assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-29 (MRO1) - A49-2 (BM1) Always Below 1 Ω
A42-29 (MRO1) or A49-2 (BM1) - Body ground Always 10 kΩ or higher
A42-30 (MRO2) - A49-1 (BM2) Always Below 1 Ω
A42-30 (MRO2) or A49-1 (BM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR