Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1391  Abnormal Leak in Accumulator  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1391 Abnormal Leak in Accumulator 351 Either of the following is detected:
1.

Accumulator pressure sensor input does not increase before braking or while the pump motor is operating.

2.

Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating.


·

Brake fluid leaks

·

Brake actuator (Brake booster with master cylinder assembly)

(Malfunctioning internal seal, low gas pressure in accumulator, etc.)


-

DTC Detection Conditions: C1391
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Accumulator pressure sensor input does not increase before braking or while the pump motor is operating ○ -
Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK FOR FLUID LEAK
a.

Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.


b.

Check that the brakes are not dragging.

OK:

There are no fluid leaks or dragging.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE APPLICABLE PART

2.RECONFIRM DTC

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1391 is output. A
DTC C1391 is not output. B



A

3.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)

B

3.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SMC/SRC/SCC)
50004 105 89
HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).




e.

Perform the Active Test of the solenoid using the GTS.


f.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

g.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator (brake booster with master cylinder assembly).



Result:
Result Proceed to
The output value of the wheel cylinder pressure sensor increases. A
The output values of the wheel cylinder pressure sensor does not increase. B



A

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT