Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU assembly is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC (TRAC) operation, and pressing and holding this switch turns off TRC (TRAC) and VSC operation. If TRC (TRAC) and VSC operations are turned off, the TRC (TRAC) OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C407571E01
0.917,0.917 1.531,1.115 0.615,0.198 10 false CANL 1.406,0.729 1.719,0.927 0.313,0.198 10 false 25 5.677,0.927 6.292,1.125 0.615,0.198 10 false CA1L 5.354,0.698 5.667,0.896 0.313,0.198 10 false 38 0.896,1.75 1.51,1.948 0.615,0.198 10 false CANH 1.406,1.542 1.719,1.74 0.313,0.198 10 false 9 5.333,1.521 5.646,1.719 0.313,0.198 10 false 37 5.688,1.74 6.302,1.938 0.615,0.198 10 false CA1H 0.198,3.885 0.656,4.083 0.458,0.198 10 false G18 0.208,4.073 1.396,4.469 1.188,0.396 10 false Combination Meter Assembly 3.604,2.74 3.76,2.938 0.156,0.198 10 false 2 3.865,2.76 4.323,2.958 0.458,0.198 10 false E 4.521,2.74 4.677,2.938 0.156,0.198 10 false + 3.552,3.25 4.01,3.448 0.458,0.198 10 false G36 3.552,3.458 5,3.938 1.448,0.479 10 false VSC OFF Switch 2.917,4.354 4.677,4.542 1.76,0.188 10 false : CAN Communication Line 5.042,3.781 5.5,3.979 0.458,0.198 10 false A42 5.042,3.99 7.073,4.385 2.031,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.75,2.75 4.99,3.01 0.24,0.26 10 false 5 5.646,2.708 6.104,2.906 0.458,0.198 10 false CSW 5.438,2.688 5.594,2.885 0.156,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (TRC (TRAC)/VSC OFF MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC (TRAC)/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC (TRAC) off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

d.

Check the indicator light and mode condition on the GTS changes according to VSC OFF Switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC (TRAC) OFF Message) VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the VSC OFF switch TRC (TRAC) OFF Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display is normal. C



A

2.INSPECT VSC OFF SWITCH

B

C

2.INSPECT VSC OFF SWITCH
a.

Turn the power switch off.



c.

Inspect the VSC OFF switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION

OK:

The VSC OFF switch operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VSC OFF SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-8 (CSW) - G36-5 (+) Always Below 1 Ω
A42-8 (CSW) or G36-5 (+) - Body ground Always 10 kΩ or higher
G36-2 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR