Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1381  Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor  


DESCRIPTION

This DTC is stored when the skid control ECU (brake booster with master cylinder assembly) receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly). This DTC may also be stored due to a temporary power source voltage drop.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1381 Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor 601 When the IG1 terminal voltage exceeds 9.5 V and the vehicle speed exceeds 3 km/h, a power supply voltage malfunction signal is received from the yaw rate sensor continuously for 10 seconds or more.
·

Acceleration sensor (Airbag sensor assembly) supply voltage shut down

·

Acceleration sensor (Airbag sensor assembly)


-

WIRING DIAGRAM

C409191E01
0.813,0.708 1.25,1.01 0.438,0.302 10 false CANL 6.031,0.719 6.5,1 0.469,0.281 10 false CA1L 0.802,1.323 1.281,1.604 0.479,0.281 10 false CANH 6.042,1.333 6.521,1.604 0.479,0.271 10 false CA1H 0.958,1.958 1.26,2.24 0.302,0.281 10 false IG2 2.115,2.104 3.031,2.448 0.917,0.344 10 false A/BAG-IG2 3.896,1.938 5.24,2.302 1.344,0.365 10 false from IG Circuit 1,2.573 1.26,2.813 0.26,0.24 10 false E1 0.99,3.167 1.25,3.396 0.26,0.229 10 false E2 0.406,4.042 2.552,4.719 2.146,0.677 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.094,4.042 0.417,4.292 0.323,0.25 10 false G70 3.438,3.146 5.208,3.458 1.771,0.313 10 false : CAN Communication Line 4.958,4.031 7.063,4.719 2.104,0.688 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.583,4.031 5.385,4.469 0.802,0.438 10 false A42 5.792,0.542 6.104,0.74 0.313,0.198 10 false 38 5.792,1.146 6.104,1.344 0.313,0.198 10 false 37 1.281,0.521 1.594,0.719 0.313,0.198 10 false 27 1.281,1.146 1.594,1.344 0.313,0.198 10 false 26 1.292,1.823 1.604,2.021 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.302,3.042 1.615,3.24 0.313,0.198 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.
C374261C50
0.219,0.583 0.583,0.865 0.365,0.281 2.771,2.823 2.24,2.333 true 0.177,0.229 0.49,0.385 0.313,0.156 10 false *a 0.281,0.635 0.74,0.833 0.458,0.198 10 false G70 2.802,2.771 3.26,2.969 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the G70 yaw rate and acceleration sensor (airbag sensor assembly) connector.


e.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


f.

Turn the power switch on (IG).


g.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G70-36 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (E TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (E TERMINAL)
a.
C374261C51
0.219,0.583 0.583,0.865 0.365,0.281 2.344,3.042 1.854,2.333 true 1.24,3.042 1.698,2.333 true 0.177,0.229 0.49,0.385 0.313,0.156 10 false *a 0.281,0.625 0.74,0.823 0.458,0.198 10 false G70 2.292,3.052 2.75,3.25 0.458,0.198 10 false E1 1.167,3.052 1.479,3.25 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-33 (E1) - Body ground Always Below 1 Ω
G70-32 (E2) - Body ground Always Below 1 Ω


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the G70 yaw rate and acceleration sensor (airbag sensor assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the power switch off.


d.

Turn the power switch on (READY).


e.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1381 is not output A
DTC C1381 is output B


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE



A

B