Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (integration control and panel assembly) is turned on while the power switch is on (IG).

Conditions required for operation standby:

(a)

The driver's door is closed.

(b)

Driver's seat belt is fastened.

(c)

The system is normal.



WIRING DIAGRAM

C407569E02
0.896,0.646 1.51,0.844 0.615,0.198 10 false CANL 0.885,1.448 1.5,1.646 0.615,0.198 10 false CANH 1.406,0.438 1.719,0.635 0.313,0.198 10 false 25 1.417,1.25 1.729,1.448 0.313,0.198 10 false 9 5.26,0.458 5.573,0.656 0.313,0.198 10 false 38 5.26,1.26 5.573,1.458 0.313,0.198 10 false 37 5.542,0.625 6.156,0.823 0.615,0.198 10 false CA1L 5.531,1.448 6.146,1.646 0.615,0.198 10 false CA1H 0.115,1.979 0.573,2.177 0.458,0.198 10 false G18 0.125,2.156 2.208,2.625 2.083,0.469 10 false Combination Meter Assembly 2.385,2.094 4.188,2.781 1.802,0.688 10 false to Main Body ECU (Multiplex Network Body ECU) 5.26,3.073 5.573,3.271 0.313,0.198 10 false 19 5.563,3.063 6.021,3.26 0.458,0.198 10 false CTY 5.563,4.865 6.177,5.063 0.615,0.198 10 false HZRI 5.26,4.885 5.573,5.083 0.313,0.198 10 false 10 3.906,3.063 4.063,3.26 0.156,0.198 10 false 1 2.01,3.542 2.729,3.781 0.719,0.24 10 false N7*1, M4*2 2.031,3.76 5,4.115 2.969,0.354 10 false Front Door Courtesy Light Switch Assembly 2.896,5.156 3.51,5.354 0.615,0.198 10 false E 3.573,5.156 3.844,5.438 0.271,0.281 10 false +B 3.896,4.885 4.156,5.094 0.26,0.208 10 false 24 2.542,4.875 2.854,5.073 0.313,0.198 10 false 15 0.594,6.219 4.26,6.417 3.667,0.198 10 false : CAN Communication Line 2.271,5.344 3.021,5.542 0.75,0.198 10 false G32 2.271,5.51 4.49,6.115 2.219,0.604 10 false Brake Hold Switch (Integration Control and Panel Assembly) 5,5.813 5.635,6.01 0.635,0.198 10 false A42 5,5.99 7.073,6.531 2.073,0.542 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.229,4.906 1.135,5.156 0.906,0.25 10 false *1: for LHD 0.25,5.292 1.156,5.542 0.906,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (integration control and panel assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver's door is closed.

2.

Driver's seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system

·

Hybrid control system



Result:
Proceed to
NEXT




NEXT

2.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)
2.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Standby Light Brake hold standby indicator light Indicator light ON/OFF Observe combination meter

d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Standby Light Brake hold standby indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
BH Standby Light
Data List Display
BH Standby Light
50004 105 73 280

e.

Check the operating condition of the brake hold standby indicator light when operating it using the GTS.

Result:
Result Proceed to
Brake hold standby indicator light in the Data List does not change using the Active Test. A
Brake hold standby indicator light in the Data List turns ON/OFF using the Active Test. B




A

B

3.INSPECT COMBINATION METER ASSEMBLY
3.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Hold Indicator
50004 409 117

c.

Check the combination meter assembly.

OK:

The brake hold standby indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

4.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY

NG

4.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

Turn the power switch off.


b.

Remove the brake hold switch (integration control and panel assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>REMOVAL


c.

Inspect the brake hold switch (integration control and panel assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>INSPECTION

OK:

The brake hold switch (integration control and panel assembly) operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - INTEGRATION CONTROL AND PANEL ASSEMBLY)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-10 (HZRI) - G32-24 (+B) Always Below 1 Ω
A42-10 (HZRI) or G32-24 (+B) - Body ground Always 10 kΩ or higher
G32-15 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Turn on the interior lights and check that they illuminate, and then set the switch so that the lights illuminate when the door is opened.


b.

Check that the lights illuminate when the driver door is opened.

OK:

The interior lights illuminate when the driver door is opened.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

7.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.
C249788C55
0.25,0.5 0.667,0.75 0.417,0.25 1.667,1.802 1.906,0.635 true 0.344,0.552 0.802,0.75 0.458,0.198 10 false A42 1.802,0.458 2.26,0.656 0.458,0.198 10 false CTY 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-19 (CTY) - Body ground Driver door open Below 1 V
A42-19 (CTY) - Body ground Driver door closed Pulse generation



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT)