The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving with lock-up on.
When the brake pedal is depressed, the stop light switch assembly sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070312 | Brake Switch "B" Circuit Short to Battery | All of the following conditions are met (2-trip detection logic):
·
The ignition switch is ON. ·
The battery voltage is 8 V or more. ·
The stop light switch assembly remains ON while the vehicle is driven in a GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (2 mph)) pattern 5 times. |
·
Short in stop light switch assembly circuit ·
Stop light switch assembly ·
TCM |
Comes on | DTC stored | SAE Code:
P0724 |
This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "stop and go" driving, the TCM interprets this as a malfunction of the stop light switch assembly, illuminates the MIL and stores this DTC. The vehicle must STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) five times for two consecutive driving cycles in order to store this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Repeat the following procedure 5 times:
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to less than 3 km/h (2 mph).
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P070312.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Strictly observe posted speed, limits, traffic laws and road conditions.
Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.
Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.
Do not operate the GTS while driving the vehicle.
Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Stop Light SW.
According to the display on the GTS, read the Data List while the vehicle is being driven.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly status | OFF or ON | ·
OFF: Brake pedal released ·
ON: Brake pedal depressed |
- |
| Tester Display |
|---|
| Stop Light SW |
On the GTS screen, ON or OFF is displayed accordingly.
In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty or not.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the stop light switch assembly installation.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Stop light switch assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the TCM connector.
| *a | Brake pedal depressed | *b | Brake pedal released |
| *c | Front view of wire harness connector
(to TCM) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-34 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
If there is a short in the STP terminal circuit, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION