Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P07757F  Pressure Control Solenoid "B" Actuator Stuck Off  


DESCRIPTION

Using the current from the TCM, the shift solenoid valve SL2 controls the C2 clutch pressure in accordance with the requested shift mode.

When the TCM requests the shift mode to be changed to belt mode, the C2 clutch is engaged and the input torque is transmitted to the output shaft via the steel belt.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07757F Pressure Control Solenoid "B" Actuator Stuck Off Any of the following conditions are met (2-trip detection logic):
·

When the TCM commands the C2 clutch to be engaged, the difference between the signals from the transmission revolution sensor (NSS) and (NOUT) is more than 300 rpm for 2 second or more.

·

When the TCM commands the C1 clutch to be engaged, the difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm for 1 second or more.


·

Transmission valve body assembly (shift solenoid valve SL2)

·

Continuously variable transaxle assembly


Comes on DTC stored SAE Code:
P0776

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition TCM commands the C2 clutch to be engaged ○ -
TCM commands the C1 clutch to be engaged - ○
Malfunction Condition Difference between the signals from the transmission revolution sensor (NSS) and (NOUT) is more than 300 rpm ○ -
Difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm - ○
Duration 2 seconds or more 1 second or more
Detection Logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

·

When the TCM requests the shift mode to be changed to belt mode, the shift solenoid valve SL2 is turned ON and the C2 clutch is engaged. As a result, the transmission revolution sensor (NSS) signal becomes equal to the transmission revolution sensor (NOUT) signal.

By comparing the signals indicating the secondary pulley revolution (speed) and output shaft revolution (speed), the TCM judges if the shift mode is belt mode or not.

When the TCM requests the shift mode to be changed to belt mode, if the difference between the transmission revolution sensor (NSS) and (NOUT) signals is more than 300 rpm, it determines the shift solenoid valve SL2 is malfunctioning, illuminates the MIL and stores this DTC.

·

Under normal conditions, when the TCM requests the shift mode be changed to gear mode, line pressure is applied from the shift solenoid SL1 to engage the C1 clutch and gear mode is entered.

When the shift solenoid valve SL2 is stuck ON, if the TCM requests the shift mode to be changed to gear mode, line pressure is applied to the clutch apply control valve from the shift solenoid valve SL2 and in turn line pressure to the C1 clutch is blocked.

As a result, the C1 clutch cannot be engaged and the shift mode cannot be changed.

In this case, when the TCM requests the shift mode to be changed to gear mode, it detects that gear mode cannot be entered (the C1 clutch is not engaged and the difference between the transmission revolution sensor (NT) signal and transmission revolution sensor (NC1) signal exceeds the threshold) and determines that the shift solenoid valve SL2 is stuck ON, illuminates the MIL and stores a DTC.

SL2 Stuck ON Detection Condition:
C398251C01
0.25,0.167 6.917,3.333 6.667,3.167 0.25,3.5 6.917,6.667 6.667,3.167 0.333,0.25 0.833,0.5 0.5,0.25 10 false *A 0.333,3.594 0.667,3.833 0.333,0.24 10 false *B 2,1.677 2.313,1.833 0.313,0.156 10 false *1 2.792,0.74 3.104,0.896 0.313,0.156 10 false *2 4.49,2.354 4.802,2.51 0.313,0.156 10 false *3 5.646,2.177 5.958,2.333 0.313,0.156 10 false *4 2,5.094 2.313,5.25 0.313,0.156 10 false *1 2.802,4.135 3.115,4.292 0.313,0.156 10 false *2 4.49,5.906 4.802,6.063 0.313,0.156 10 false *3 5.656,5.573 5.969,5.729 0.313,0.156 10 false *4 2.771,3.646 3.083,3.802 0.313,0.156 10 false *a
*A TCM commands C1 clutch engagement when shift solenoid valve SL2 normal *B TCM commands C1 clutch engagement when shift solenoid valve SL2 stuck ON
*1 Shift Solenoid Valve SL1 *2 Shift Solenoid Valve SL2
*3 Clutch Apply Control Valve *4 C1 Clutch
*a Shift solenoid valve SL2 stuck ON - -
V100135

Oil Pressure Flow
V113148

Valve Movement



CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P07757F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If any DTCs other than P07757F are output, perform troubleshooting for those DTCs first.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P07757F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:
·

If DTC P077512 or P077514 is output, perform troubleshooting for that DTC first.

·

If DTCs P077512 and P077514 are not output but DTC P281F00 is output, perform troubleshooting for DTC P281F00 first.




Result:
Result Proceed to
Only DTC P07757F is output A
DTC P07457F and P07757F are output B
DTC P07757F and P077512 are output C
DTC P07757F and P077514 are output D
DTC P07757F and P281F00 are output E
DTC P07757F and DTCs other than P074512, P074514, P07457F and P281F00 are output F



A

2.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL2)

B

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1)

C

D

E

F

2.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL2)
a.

Disconnect the transmission wire connector from the shift solenoid valve SL2.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL

C398705C01
2.969,1.531 3.635,1.531 true 4.833,1.25 5.25,1.583 true 5.5,1.583 5.917,1.25 true 1.167,0.167 1.479,0.323 0.313,0.156 10 false *1 3.677,1.458 3.99,1.615 0.313,0.156 10 false *2 4.552,0.729 4.865,0.885 0.313,0.156 10 false *a 4.719,1.177 5.031,1.333 0.313,0.156 10 false 2 5.958,1.177 6.271,1.333 0.313,0.156 10 false 1 5.552,2.427 6.01,2.625 0.458,0.198 10 false (+) 5.063,2.427 5.521,2.625 0.458,0.198 10 false (-)
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SL2
*a Component without harness connected
(Shift Solenoid Valve SL2)
- -



b.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SL2 connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

4.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
a.

Replace the transmission valve body assembly.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1)
a.

Disconnect the transmission wire connector from the shift solenoid valve SL1.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL

C398704C01
2.979,1.104 3.563,1.104 true 4.833,1.25 5.25,1.583 true 5.5,1.583 5.917,1.25 true 1.188,0.167 1.5,0.323 0.313,0.156 10 false *1 3.615,1.031 3.927,1.188 0.313,0.156 10 false *2 4.583,0.76 4.896,0.917 0.313,0.156 10 false *a 4.719,1.177 4.875,1.375 0.156,0.198 10 false 2 5.969,1.167 6.125,1.365 0.156,0.198 10 false 1 5.563,2.385 6.021,2.583 0.458,0.198 10 false (+) 5.052,2.385 5.51,2.583 0.458,0.198 10 false (-)
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SL1
*a Component without harness connected
(Shift Solenoid Valve SL1)
- -



b.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SL1 connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL2)

NG

6.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
6.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
a.

Replace the transmission valve body assembly.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT