Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2018.10–2019.09
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0371711 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

*3: When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

*4: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
Front exhaust pipe assembly*4 GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Starter assembly*3 Clear the number of starter operations Stop and start system (Click here)
·

Engine assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Continuously variable transaxle assembly Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
TCM If transaxle compensation code read from TCM
·

Transfer transaxle compensation code

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


If transaxle compensation code not read from TCM
·

Reset transaxle compensation code

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11361J 3.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101G 4.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C402351

Turn the crankshaft to gain access to the 6 drive plate and torque converter setting bolts and remove each drive plate and torque converter setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter setting bolt.



Hide 45319 7.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 8.DISCONNECT WIRE HARNESS (for LHD)

Hide 9.DISCONNECT WIRE HARNESS (for RHD)

Hide 82121 11.DISCONNECT ENGINE WIRE

a.
C402274C01
1.354,0.365 2.333,0.167 2.333,0.167 2.5,0.167 true 2.167,1.333 2.833,0.667 2.833,0.667 3,0.667 true 2.542,0.104 2.771,0.313 0.229,0.208 10 true *1 3.031,0.594 3.25,0.76 0.219,0.167 10 true *2
*1 Camshaft Position Sensor Connector
*2 Engine Coolant Temperature Sensor Connector


Remove the bolt and 2 nuts to disconnect the engine wire from the engine assembly.


b.

Disconnect the camshaft position sensor connector.


c.

Disconnect the engine coolant temperature sensor connector.


d.
C402275C01
2.25,1.396 2.51,2.01 2.51,2.01 2.875,2.01 true 2.906,1.938 3.104,2.135 0.198,0.198 10 true *1
*1 Flow Shutting Valve (Water Valve) Connector


Disconnect the flow shutting valve (water valve) connector.


e.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


f.

Detach the clamp to disconnect the engine wire.


g.

Detach the claw, rotate the lever and disconnect the transmission wire connector.

C402276C02
2.25,0.031 2.458,0.188 0.208,0.156 10 true *a 3.146,0.042 3.375,0.208 0.229,0.167 10 true *b 2.823,1.313 3.042,1.5 0.219,0.188 10 true *c 3.458,0.5 3.667,0.667 0.208,0.167 10 true *d 3.594,2.219 3.906,2.375 0.313,0.156 10 false *e 3.219,1.49 3.417,1.688 0.198,0.198 10 true *f 2.938,2.323 3.25,2.479 0.313,0.156 10 false *g 2.323,1.323 2.542,1.521 0.219,0.198 10 true *h 2.344,2.188 2.5,2.385 0.156,0.198 10 false i
*a Transmission Wire Connector *b Shift Stroke Sensor Connector
*c Park/Neutral Position Switch Connector *d Transmission Revolution Sensor (NOUT) Connector
*e TCM Connector *f Transmission Revolution Sensor (NSS) Connector
*g Oil Pressure Sensor Connector *h Transmission Revolution Sensor (NT) Connector
*i Oil Pump With Motor Assembly Connector - -
V113147

Remove in this Direction - -



h.

Disconnect the shift stroke sensor connector.


i.

Disconnect the park/neutral position switch connector.


j.

Disconnect the transmission revolution sensor (NOUT) connector.


k.

Detach the claw, rotate the lever and disconnect the TCM connector.


l.

Disconnect the transmission revolution sensor (NSS) connector.


m.

Disconnect the oil pressure sensor connector.


n.

Disconnect the transmission revolution sensor (NT) connector.


o.

Disconnect the oil pump with motor assembly connector.


p.

Remove the 3 bolts to disconnect the engine wire from the continuously variable transaxle assembly.


q.

Detach the 5 clamps to disconnect the engine wire.


r.
C405168C01
0.042,0.042 0.354,0.24 0.313,0.198 10 true *A 0.042,2.531 0.354,2.729 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Detach the 2 clamps to disconnect the engine wire.


Hide 89535B 12.REMOVE TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.


a.
C402285

Remove the 2 bolts and TCM from the continuously variable transaxle assembly.


Hide 16261G 13.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
C402278

Slide the hose clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.


b.

Detach the 2 clamps.


Hide 16264D 14.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
C407587

Slide the hose clip and disconnect the No. 2 water by-pass hose from the transmission oil cooler.


b.

Remove the bolt and No. 2 water by-pass hose from the water hose clamp bracket.


Hide 16206 15.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
C402359C02
1.917,1.833 2.417,1.833 true 1,0.25 1.5,0.25 true 1.948,0.385 2.448,0.385 true 2.448,1.771 2.76,1.927 0.313,0.156 10 false *1 0.813,0.177 1,0.365 0.188,0.188 10 true *2 2.49,0.323 2.802,0.479 0.313,0.156 10 false *3
*1 Water By-pass Pipe Sub-assembly
*2 No. 3 Water By-pass Hose
*3 No. 4 Water By-pass Hose


Slide the 2 hose clips and disconnect the No. 3 water by-pass hose and No. 4 water by-pass hose from the water by-pass pipe sub-assembly.


b.
C402279

Remove the 3 bolts and water by-pass pipe sub-assembly from the continuously variable transaxle assembly.


Hide 32942N 16.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE

Hide 32941R 17.DISCONNECT OIL COOLER INLET HOSE

Hide 33493A 18.REMOVE TRANSMISSION OIL COOLER

Hide 12361 19.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
C405166

Remove the bolt and front engine mounting insulator from the transverse engine engine mounting bracket.


Hide 12311A 20.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C405229

Remove the 3 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.


Hide 11363A 22.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 12303 24.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C407594

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the continuously variable transaxle assembly.


Hide 30400 25.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C402280C01
2.146,0.156 2.229,0.385 0.083,0.229 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A), (B): Remove from continuously variable transaxle assembly side.

·

Bolt (C): Remove from engine assembly side.




Hide 32000A 26.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C402281

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 27.REMOVE TRANSAXLE HOUSING TYPE T OIL SEAL

NOTICE:
·

Do not remove the stator shaft assembly from the CVT main body as there is a possibly of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C398797E01
1.583,2.667 1.583,2.25 false 1.479,2.677 1.938,2.875 0.458,0.198 10 false SST

Using SST, remove the transaxle housing type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.



Hide 12304 28.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

a.
C405163

Remove the 5 bolts and engine mounting bracket sub-assembly LH from the continuously variable transaxle assembly.


Hide 29.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C402286

Remove the 6 bolts and 5 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 16575D 30.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

a.
C402287

Remove the 2 bolts and No. 1 water hose clamp bracket from the continuously variable transaxle assembly.


Hide 33823 31.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C402288

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 35150B 32.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C407583C01
0.198,0.115 0.469,0.354 0.271,0.24 12 false *A 1.521,0.115 1.833,0.354 0.313,0.24 12 false *B
*A for Type A
*B for Type B


for Type A:

i.

Remove the transmission case plug assembly from the continuously variable transaxle assembly.



b.

for Type B:

i.

Remove the transmission case plug assembly from the continuously variable transaxle assembly.


ii.

Remove the O-ring from the transmission case plug assembly.



Hide 33.REMOVE BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the breather plug sub-assembly is necessary.


a.
C398784

Remove the breather plug sub-assembly from the continuously variable transaxle assembly.


b.
C398785C01
1.115,0.333 1.531,0.333 false 1.219,1.042 1.552,1.042 false 1.417,2.031 1.75,2.031 false 0.938,0.25 1.25,0.406 0.313,0.156 10 false *1 1.063,0.979 1.375,1.135 0.313,0.156 10 false *2 1.26,1.958 1.573,2.115 0.313,0.156 10 false *3
*1 Breather Plug Cap
*2 Breather Plug
*3 O-ring


Remove the breather plug cap from the breather plug.


c.

Remove the O-ring from the breather plug.


Hide 32000A 34.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 35.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY