Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P091414  Gear Shift Position Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P091412.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P091412

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P091414 Gear Shift Position Circuit Short to Ground or Open A short to ground or open is detected in the shift stroke sensor circuit for 5 seconds or more (1-trip detection logic).
·

Shift stroke sensor

·

Harness and connector

·

TCM


Comes on DTC stored SAE Code:
P0916

MONITOR DESCRIPTION

This DTC indicates an open or short to ground in the shift stroke sensor circuit. If there is an open or short to ground in the shift stroke sensor circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P091414.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TCM (VDD VOLTAGE)
a.
C399105C07
1.49,0.188 1.906,0.438 0.417,0.25 1.833,1.156 2.5,0.906 true 0.875,1.677 1.542,1.427 true 1.583,0.24 2.042,0.438 0.458,0.198 10 false C39 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.552,0.833 3.01,1.031 0.458,0.198 10 false VDD 0.542,1.604 1,1.802 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Shift Stroke Sensor)


Disconnect the shift stroke sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C39-2 (VDD) - C39-3 (GND) Ignition switch ON 4.7 to 5.3 V



d.

Connect the shift stroke sensor connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TCM)

NG

5.CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TCM)
2.CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TCM)
a.

Disconnect the C39 shift stroke sensor connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-4 (VOUT) - C33-46 (SFV) Always Below 1 Ω
C39-4 (VOUT) or C33-46 (SFV) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the C39 shift stroke sensor connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT SHIFT STROKE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT STROKE SENSOR
a.

Connect 3 new dry-cell batteries (1.5 V each) in series.


b.

Prepare a magnet or equivalent tool.


c.

Remove the shift stroke sensor.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>SHIFT STROKE SENSOR>REMOVAL


d.

Connect a positive (+) lead from the batteries to terminal 2 (VDD) and a negative (-) lead to terminal 3 (GND).

C399402C01
5.083,3.083 5.667,2.5 5.667,2.5 5.917,2.5 true 2.25,1.927 2.667,2.26 true 1.51,2.271 1.927,1.938 true 1.521,1.375 1.938,1.708 true 0.573,0.292 0.885,0.448 0.313,0.156 10 false *a 5.646,2.865 5.958,3.021 0.313,0.156 10 false *b 0.552,1.677 0.865,1.833 0.313,0.156 10 false *c 5.958,2.417 6.271,2.573 0.313,0.156 10 false *d 4.125,3.302 4.323,3.479 0.198,0.177 10 false *e 4.594,0.479 4.906,0.635 0.313,0.156 10 false *b 1.198,1.302 1.656,1.5 0.458,0.198 10 false VDD 1.094,2.208 1.552,2.406 0.458,0.198 10 false VOUT 2.708,2.198 3.167,2.396 0.458,0.198 10 false GND
*a Component without harness connected
(Shift Stroke Sensor)
*b Magnet Movement Direction
*c Dry Cell Battery *d Magnet
*e 2.6 mm or less - -



e.

Wave the magnet left and right 2.6 mm (0.102 in.) or less from the tip of the shift stroke sensor to output a high/low signal while measuring the voltage.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (Combined Dry-cell Battery Voltage of 4.5 V):
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.09 to 4.19 V
Low signal 0.36 to 0.45 V


Reference Voltage (Combined Dry-cell Battery Voltage of 5.0 V):
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.55 to 4.65 V
Low signal 0.4 to 0.5 V



g.

Install the shift stroke sensor.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>SHIFT STROKE SENSOR>INSTALLATION


Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

4.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TCM)
a.

Disconnect the C39 shift stroke sensor connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-2 (VDD) - C33-45 (VCSF) Always Below 1 Ω
C39-3 (GND) - C33-44 (E2SF) Always Below 1 Ω
C39-2 (VDD) or C33-45 (VCSF) - Body ground and other terminals Always 10 kΩ or higher
C39-3 (GND) or C33-44 (E2SF) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the C39 shift stroke sensor connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT