Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Dimmer Signal Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends an auto dimmer signal to the radio receiver assembly via this circuit.

When the radio receiver assembly receives an auto dimmer signal from the main body ECU (multiplex network body ECU), the radio receiver assembly causes the instrument panel illumination to be dimmed.

WIRING DIAGRAM

E408091E01
5.448,2.719 7.115,3.01 1.667,0.292 10 false Radio Receiver Assembly 0.708,2.688 2.896,3.26 2.188,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 1.302,1.552 1.792,1.75 0.49,0.198 10 false ACAN 5.51,1.563 6.031,1.76 0.521,0.198 10 false ADIM 5.458,2.542 5.885,2.76 0.427,0.219 10 false G67 5.25,1.427 5.448,1.615 0.198,0.188 10 false 3 1.833,1.417 2.031,1.604 0.198,0.188 10 false 8 0.729,2.51 1.156,2.729 0.427,0.219 10 false G44

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the radio receiver assembly connector.


b.
E408087C02
1.5,0.521 1.917,0.833 0.417,0.313 0.729,1.125 0.906,1.125 0.906,1.125 1.052,1.802 true 1.594,0.594 2.052,0.792 0.458,0.198 10 false G67 0.083,0.083 0.542,0.281 0.458,0.198 10 false *a 0.354,1.042 0.813,1.24 0.458,0.198 10 false ADIM
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G67-3 (ADIM) - Body ground Ignition switch ON, automatic light control sensor covered by hand, and light control switch in AUTO position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the G44 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the G67 radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G44-8 (ACAN) - G67-3 (ADIM) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR