Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Main Body" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Main Body" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Main body ECU (multiplex network body ECU) branch wire or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly



WIRING DIAGRAM

C409781E02
0.135,1.521 0.594,1.719 0.458,0.198 10 false G96 0.146,1.667 2.208,1.969 2.063,0.302 10 false No. 1 CAN Junction Connector 1.583,0.438 2.042,0.635 0.458,0.198 10 false 4 1.573,1.083 2.031,1.281 0.458,0.198 10 false 15 5.448,0.542 5.906,0.74 0.458,0.198 10 false G44 5.5,0.313 5.99,0.51 0.49,0.198 10 false 5 5.531,1 6.021,1.198 0.49,0.198 10 false 4 5.844,0.531 6.302,0.729 0.458,0.198 10 false CANH 5.854,1.208 6.313,1.406 0.458,0.198 10 false CANL 1.865,2.604 2.813,2.885 0.948,0.281 10 false ECU-B NO.3 2.844,2.49 3.677,2.74 0.833,0.25 10 false 4D 2.844,2.271 3.677,2.521 0.833,0.25 10 false 23 5.531,2.479 5.99,2.698 0.458,0.219 10 false A 5.5,2.26 5.958,2.479 0.458,0.219 10 false 31 5.854,2.479 6.313,2.698 0.458,0.219 10 false BECU 5.531,3.542 5.99,3.76 0.458,0.219 10 false A 5.51,3.323 5.969,3.542 0.458,0.219 10 false 30 5.844,3.552 6.302,3.771 0.458,0.219 10 false ACC 4.49,3.406 5.271,3.677 0.781,0.271 10 false ECU-ACC 5.521,4.885 5.979,5.104 0.458,0.219 10 false A 5.5,4.667 5.958,4.885 0.458,0.219 10 false 32 5.844,4.885 6.302,5.104 0.458,0.219 10 false IG 5.844,7.146 6.302,7.365 0.458,0.219 10 false GND1 5.51,7.156 5.969,7.375 0.458,0.219 10 false A 5.479,6.906 5.938,7.125 0.458,0.219 10 false 11 2.844,7.167 3.677,7.417 0.833,0.25 10 false 4D 2.875,6.938 3.708,7.188 0.833,0.25 10 false 3 2.833,6.458 3.667,6.708 0.833,0.25 10 false 4A 2.844,6.25 3.677,6.5 0.833,0.25 10 false 17 3.479,6.74 4.625,7.052 1.146,0.313 10 false IG1 NO.2 3.5,5.406 4.552,5.75 1.052,0.344 10 false IG1 NO.1 3.646,4.063 4.479,4.313 0.833,0.25 10 false ACC 2.833,3.073 3.667,3.323 0.833,0.25 10 false 4K 2.875,2.865 3.708,3.115 0.833,0.25 10 false 1 2.833,3.802 3.667,4.052 0.833,0.25 10 false 4A 2.833,3.594 3.667,3.844 0.833,0.25 10 false 30 0.542,3.042 2,3.365 1.458,0.323 10 false from Auxiliary Battery 0.135,6.448 2.042,6.865 1.906,0.417 10 false from Certification ECU (Smart Key ECU Assembly) 2.771,8.031 4.688,8.521 1.917,0.49 10 false Instrument Panel Junction Block Assembly 5.052,8.042 6.719,8.438 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.396,4.76 5.365,5.156 0.969,0.396 10 false ECU-IG1 NO.4 0.125,3.792 2.031,4.208 1.906,0.417 10 false from Certification ECU (Smart Key ECU Assembly) 0.146,2.469 1.604,2.792 1.458,0.323 10 false from Auxiliary Battery 5.448,1.198 5.906,1.396 0.458,0.198 10 false G44



CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C369119C28
1.583,0.167 2,0.417 0.417,0.25 2.188,0.917 2.354,0.917 2.354,0.917 2.5,1.531 true 2.333,0.75 2.5,0.75 2.5,0.75 2.719,1.563 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.667,0.219 1.979,0.417 0.313,0.198 10 false G44 1.917,0.688 2.396,0.896 0.479,0.208 10 false CANH 1.823,0.865 2.302,1.073 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G44-5 (CANH) - G44-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

b.

Connect the instrument panel junction block assembly connectors.


c.
C227508C42
1.531,0.552 1.917,0.792 0.385,0.24 3,1.073 2.76,0.438 2.76,0.438 2.646,0.438 true 3.094,1.115 3.01,1.594 3.01,1.594 2.875,1.594 true 2.917,1.083 2.74,0.771 2.74,0.771 2.625,0.771 true 1.219,1.083 1.135,0.771 1.135,0.771 1.021,0.771 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.667,0.583 1.979,0.74 0.313,0.156 10 false A 2.188,0.375 2.625,0.552 0.438,0.177 10 false BECU 2.25,0.719 2.688,0.896 0.438,0.177 10 false ACC 2.677,1.531 3.115,1.708 0.438,0.177 10 false IG 0.552,0.698 0.99,0.875 0.438,0.177 10 false GND1
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



d.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-31 (BECU) - Body ground Power switch off 11 to 14 V
A-30 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
Power switch off Below 1 V
A-32 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the instrument panel junction block assembly connectors.

B532774C02
1.875,0.167 2.292,0.417 0.417,0.25 5.083,0.563 5.5,0.813 0.417,0.25 2.021,0.219 2.333,0.417 0.313,0.198 10 false 4D 5.198,0.604 5.51,0.802 0.313,0.198 10 false 4K 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Power switch off 11 to 14 V
4D-23 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the instrument panel junction block assembly connector.


b.
B532775C01
1.594,0.26 2.021,0.51 0.427,0.25 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.698,0.281 2.01,0.479 0.313,0.198 10 false 4A
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4A-30 - Body ground Power switch on (ACC) 11 to 14 V
Power switch off Below 1 V
4A-17 - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG