Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the parking assist ECU determines that the input/output signal communication with the television camera assembly is abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Television camera assembly power supply malfunction
·

Harness or connector

·

Television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E240924E68
1.625,0.469 1.99,0.688 0.365,0.219 10 false CB+ 1.521,1.281 2.25,1.479 0.729,0.198 10 false CGND 5.438,1.75 6.26,1.99 0.823,0.24 10 false N24 0.656,1.594 1.042,1.792 0.385,0.198 10 false R15 0.667,1.771 2.583,2.031 1.917,0.26 10 false Television Camera Assembly 5.438,1.917 6.771,2.271 1.333,0.354 10 false Parking Assist ECU 5.594,0.458 6.052,0.656 0.458,0.198 10 false CB+ 5.594,1.26 6.052,1.458 0.458,0.198 10 false CGND 5.271,0.354 5.729,0.552 0.458,0.198 10 false 33 5.281,1.156 5.74,1.354 0.458,0.198 10 false 32 2.063,1.156 2.521,1.354 0.458,0.198 10 false 5 2.052,0.354 2.51,0.552 0.458,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the R15 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-33 (CB+) - R15-6 (CB+) Always Below 1 Ω
N24-32 (CGND) - R15-5 (CGND) Always Below 1 Ω
N24-33 (CB+) or R15-6 (CB+) - Body ground Always 10 kΩ or higher
N24-32 (CGND) or R15-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E407111C02
1.417,0.25 1.917,0.5 0.5,0.25 1.438,1.146 1.208,1.906 1.208,1.906 0.958,1.906 true 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.646,1.823 1.115,2.021 0.469,0.198 10 false CB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-32 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-33 (CB+) - N24-32 (CGND) Engine switch on (IG) 5.5 to 7.05 V
N24-33 (CB+) - N24-32 (CGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG