Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  C1682  Front Camera Current Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1682 Front Camera Current Malfunction Open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E240924E70
5.573,0.458 6.208,0.74 0.635,0.281 10 false BCB+ 5.281,0.375 5.583,0.542 0.302,0.167 10 false 15 5.583,1.26 6.271,1.448 0.688,0.188 10 false BGND 1.531,0.469 1.969,0.677 0.438,0.208 10 false BCB+ 1.521,1.271 1.958,1.49 0.438,0.219 10 false BGND 5.385,1.729 6,1.896 0.615,0.167 10 false N24 0.573,1.563 0.948,1.729 0.375,0.167 10 false B12 0.573,1.729 2.781,2.146 2.208,0.417 10 false Front Television Camera Assembly 5.385,1.917 6.948,2.26 1.563,0.344 10 false Parking Assist ECU 5.281,1.177 5.542,1.344 0.26,0.167 10 false 37 2.052,0.365 2.156,0.531 0.104,0.167 10 false 6 2.063,1.177 2.167,1.344 0.104,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the B12 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-15 (BCB+) - B12-6 (BCB+) Always Below 1 Ω
N24-37 (BGND) - B12-5 (BGND) Always Below 1 Ω
N24-15 (BCB+) or B12-6 (BCB+) - Body ground Always 10 kΩ or higher
N24-37 (BGND) or B12-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E407111C03
1.417,0.25 1.917,0.5 0.5,0.25 1.073,0.979 0.917,0.365 0.917,0.365 0.667,0.365 true 1.073,1.167 0.865,1.906 0.865,1.906 0.615,1.906 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.26,0.281 0.729,0.479 0.469,0.198 10 false BCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.188,1.823 0.75,2.01 0.563,0.188 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-37 (BGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-15 (BCB+) - N24-37 (BGND) Engine switch on (IG) 5.5 to 7.05 V
N24-15 (BCB+) - N24-37 (BGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG