Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  C1687  Over Current Detected in Driver Side Camera  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1687 Over Current Detected in Driver Side Camera Side camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH (for LHD)

·

Outer rear view mirror assembly LH (for LHD)

·

Side television camera assembly RH (for RHD)

·

Outer rear view mirror assembly RH (for RHD)



WIRING DIAGRAM

for LHD


E380693E23
0.802,2.26 3.74,2.448 2.938,0.188 10 false Outer Rear View Mirror Assembly LH 0.813,2.094 1.292,2.26 0.479,0.167 10 false J13 0.594,1.417 0.771,1.635 0.177,0.219 10 false A 0.563,1.583 3.458,1.969 2.896,0.385 10 false Side Television Camera Assembly LH 1.573,0.479 1.708,0.625 0.135,0.146 10 false 1 1.583,0.948 1.719,1.094 0.135,0.146 10 false 5 1.052,0.573 1.542,0.729 0.49,0.156 10 false SCB+ 1.042,1.063 1.563,1.208 0.521,0.146 10 false SGND 3.427,0.479 3.927,0.667 0.5,0.188 10 false LCB+ 3.958,0.479 4.094,0.667 0.135,0.188 10 false 3 3.406,0.948 3.906,1.104 0.5,0.156 10 false LGND 3.958,0.948 4.125,1.125 0.167,0.177 10 false 11 5.646,1.781 7.073,2.073 1.427,0.292 10 false Parking Assist ECU 5.646,1.615 5.979,1.813 0.333,0.198 10 false N24 5.948,0.604 6.469,0.76 0.521,0.156 10 false LCB+ 5.948,1.073 6.458,1.229 0.51,0.156 10 false LGND 5.677,0.469 5.865,0.635 0.188,0.167 10 false 12 5.677,0.958 5.865,1.125 0.188,0.167 10 false 35


for RHD


E380693E22
0.927,2.24 3.865,2.427 2.938,0.188 10 false Outer Rear View Mirror Assembly RH 0.927,2.083 1.406,2.25 0.479,0.167 10 false I13 0.583,1.385 0.76,1.604 0.177,0.219 10 false B 0.573,1.552 3.469,1.938 2.896,0.385 10 false Side Television Camera Assembly RH 1.573,0.479 1.708,0.625 0.135,0.146 10 false 1 1.583,0.958 1.719,1.104 0.135,0.146 10 false 5 1.063,0.573 1.552,0.729 0.49,0.156 10 false SCB+ 1.052,1.052 1.573,1.198 0.521,0.146 10 false SGND 3.385,0.49 3.906,0.635 0.521,0.146 10 false RCB+ 3.958,0.49 4.094,0.635 0.135,0.146 10 false 3 3.375,0.958 3.875,1.115 0.5,0.156 10 false RGND 3.958,0.958 4.292,1.125 0.333,0.167 10 false 11 5.688,1.813 7.115,2.104 1.427,0.292 10 false Parking Assist ECU 5.698,1.635 6.031,1.833 0.333,0.198 10 false N24 5.948,0.604 6.469,0.76 0.521,0.156 10 false RCB+ 5.948,1.073 6.458,1.229 0.51,0.156 10 false RGND 5.646,0.5 5.865,0.677 0.219,0.177 10 false 40 5.646,0.969 5.833,1.135 0.188,0.167 10 false 17


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

C

7.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the J13 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-12 (LCB+) - J13-3 (LCB+) Always Below 1 Ω
N24-35 (LGND) - J13-11 (LGND) Always Below 1 Ω
N24-12 (LCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
N24-35 (LGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU
a.
E407111C05
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.542,0.281 2.042,0.438 0.5,0.156 10 false N24
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-12 (LCB+) - N24-35 (LGND) Engine switch on (IG) 5.5 to 7.05 V
N24-12 (LCB+) - N24-35 (LGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E407112C05
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 0.74,3.083 1.354,3.281 0.615,0.198 10 false LGND 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.458,2.323 1.073,2.521 0.615,0.198 10 false J13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Disconnect the side television camera assembly LH connector.


b.

Disconnect the outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (SCB+) - J13-3 (LCB+) Always Below 1 Ω
A-5 (SGND) - J13-11 (LGND) Always Below 1 Ω
A-1 (SCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
A-5 (SGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1684 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the I13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-40 (RCB+) - I13-3 (RCB+) Always Below 1 Ω
N24-17 (RGND) - I13-11 (RGND) Always Below 1 Ω
N24-40 (RCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
N24-17 (RGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK PARKING ASSIST ECU
a.
E407111C04
1.417,0.25 1.917,0.5 0.5,0.25 0.698,0.677 0.875,0.677 0.875,0.677 0.938,1 true 0.854,1.146 0.719,1.75 0.719,1.75 0.542,1.75 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.146,1.656 0.615,1.854 0.469,0.198 10 false RCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.281,0.594 0.844,0.781 0.563,0.188 10 false RGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-17 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-40 (RCB+) - N24-17 (RGND) Engine switch on (IG) 5.5 to 7.05 V
N24-40 (RCB+) - N24-17 (RGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E407112C03
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false RCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 0.74,3.083 1.354,3.281 0.615,0.198 10 false RGND 0.833,0.875 1.448,1.073 0.615,0.198 10 false B 0.458,2.323 1.073,2.521 0.615,0.198 10 false I13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (SCB+) - I13-3 (RCB+) Always Below 1 Ω
B-5 (SGND) - I13-11 (RGND) Always Below 1 Ω
B-1 (SCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
B-5 (SGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

10.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG