Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379920 AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System)  B1653  Driver Side Seat Position Sensor  


DESCRIPTION

The front seat adjuster assembly LH (seat position airbag sensor) circuit consists of the airbag sensor assembly and front seat adjuster assembly LH (seat position airbag sensor).

DTC B1653 is stored when a malfunction is detected in the front seat adjuster assembly LH (seat position airbag sensor) circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1653 Driver Side Seat Position Sensor One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front seat adjuster assembly LH (seat position airbag sensor) circuit for 2 seconds.

·

A front seat adjuster assembly LH (seat position airbag sensor) malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat inner belt assembly LH

·

Front seat adjuster assembly LH (seat position airbag sensor)

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C411810E01
2.167,1.125 2.396,1.323 0.229,0.198 10 false 2 2.156,2.583 2.385,2.781 0.229,0.198 10 false 1 3.583,1.125 4.073,1.333 0.49,0.208 10 false LSP+ 3.604,2.594 4.094,2.802 0.49,0.208 10 false LSP- 5.729,2.729 6.219,2.938 0.49,0.208 10 false LSP- 5.729,1.25 6.219,1.458 0.49,0.208 10 false LSP+ 5.396,1.125 5.635,1.344 0.24,0.219 10 false 25 5.396,2.604 5.635,2.823 0.24,0.219 10 false 26 5.5,3.813 5.99,4.021 0.49,0.208 10 false N21 5.5,4.031 7.135,4.292 1.635,0.26 10 false Airbag Sensor Assembly 2.573,3.198 2.875,3.396 0.302,0.198 10 false N35 0.333,3.198 0.823,3.406 0.49,0.208 10 false z18 0.323,3.438 2.385,3.792 2.063,0.354 10 false Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor) 2.583,3.438 4.823,3.667 2.24,0.229 10 false Front Seat Inner Belt Assembly LH 4.115,1.115 4.344,1.313 0.229,0.198 10 false 4 4.104,2.604 4.333,2.802 0.229,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat adjuster assembly LH (seat position airbag sensor).


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

2.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C376775C02
0.573,0.979 0.885,1.135 0.313,0.156 10 false *1 2.615,1.417 2.927,1.573 0.313,0.156 10 false *2 1.302,0.74 1.615,0.896 0.313,0.156 10 false *3 1.771,0.75 2.083,0.906 0.313,0.156 10 false *4
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Floor Wire


Disconnect the connectors from the airbag sensor assembly and front seat adjuster assembly LH (seat position airbag sensor).


b.

Check that the connectors (on the airbag sensor assembly side and front seat adjuster assembly LH (seat position airbag sensor) side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

3.CHECK FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR) CIRCUIT

Connectors are deformed or damaged

REPLACE FLOOR WIRE OR FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR) CIRCUIT
a.
C411589C02
2.375,3.5 2.885,3.74 0.51,0.24 0.729,0.615 1.24,0.854 0.51,0.24 0.938,3.802 1.125,3.802 1.125,3.802 1.531,3.917 true 1.042,3.573 1.229,3.573 1.229,3.573 1.615,3.917 true 2.031,4.448 1.844,4.448 1.844,4.448 1.74,4.323 true 0.438,2.344 0.75,2.5 0.313,0.156 10 false *1 2.823,2.719 3.135,2.875 0.313,0.156 10 false *2 1.229,2.063 1.542,2.219 0.313,0.156 10 false *3 1.823,2.042 2.135,2.198 0.313,0.156 10 false *4 2.104,4.333 2.417,4.49 0.313,0.156 10 false *5 2.385,1.833 2.542,2.031 0.156,0.198 10 false A 2.073,1.833 2.229,2.031 0.156,0.198 10 false B 1.625,1.823 1.781,2.021 0.156,0.198 10 false C 1.479,1.823 1.635,2.021 0.156,0.198 10 false D 1.021,1.813 1.177,2.01 0.156,0.198 10 false E 0.708,1.823 0.865,2.021 0.156,0.198 10 false F 0.573,3.083 0.885,3.24 0.313,0.156 10 false *b 0.625,0.25 0.938,0.406 0.313,0.156 10 false *a 0.552,3.729 0.979,3.927 0.427,0.198 10 false LSP+ 0.667,3.479 1.094,3.677 0.427,0.198 10 false LSP- 0.865,0.635 1.292,0.833 0.427,0.198 10 false z18 2.5,3.542 2.927,3.74 0.427,0.198 10 false N21
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor))
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z18-1 - Body ground Engine switch on (IG) Below 1 V
z18-2 - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z18-1 - z18-2 Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z18-1 - z18-2 Always 1 MΩ or higher
z18-1 - Body ground Always 1 MΩ or higher
z18-2 - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

7.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
4.CHECK DTC
a.
C391329C01
0.854,1.063 1.167,1.26 0.313,0.198 10 false *1 2.021,1.438 2.333,1.635 0.313,0.198 10 false *2
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat adjuster assembly LH (seat position airbag sensor).


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the engine switch on (IG), and wait for at least 60 seconds.


d.

e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1653 is not output
DTC B1653 is output


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.




DTC B1653 is not output

DTC B1653 is output

5.REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR)
5.REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (SEAT POSITION AIRBAG SENSOR)
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat adjuster assembly LH (seat position airbag sensor).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY

HINT:

Perform the inspection using parts from a normal vehicle if possible.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.
C391329C04
0.854,1.063 1.167,1.26 0.313,0.198 10 false *1 2.021,1.438 2.333,1.635 0.313,0.198 10 false *2
*1 Front Seat Adjuster Assembly LH (Seat Position Airbag Sensor)
*2 Airbag Sensor Assembly


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG), and wait for at least 60 seconds.


c.

d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1653 is not output
DTC B1653 is output


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.




DTC B1653 is not output

END (FRONT SEAT ADJUSTER ASSEMBLY LH [SEAT POSITION AIRBAG SENSOR] WAS DEFECTIVE)

DTC B1653 is output

7.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.

Remove the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL


b.

Inspect the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE FLOOR WIRE

NG