The side collision sensor RH circuit consists of the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.
The No. 2 side airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.
DTC B1633 is stored when a malfunction is detected in the circuit for the side collision sensor RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1633 | Curtain Shield Airbag Sensor Initialization Error (RH) | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds. ·
A No. 2 side airbag sensor assembly RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Floor wire ·
Front door wire RH ·
No. 2 side airbag sensor assembly RH ·
Airbag sensor assembly |
Comes on | Not applicable |
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1632 is not output |
| DTC B1632 is output |
DTC B1632 is not output
DTC B1632 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and No. 2 side airbag sensor assembly RH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and No. 2 side airbag sensor assembly RH.
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
Check that the connectors (on the airbag sensor assembly side and No. 2 side airbag sensor assembly RH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M16-4 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| M16-3 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M16-4 (BCR+) - M16-3 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M16-4 (BCR+) - M16-3 (BCR-) | Always | 1 MΩ or higher |
| M16-4 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M16-3 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors to them.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1633 is output |
| DTC B1638 is output |
| DTCs B1633 and B1638 are not output |
Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.
DTC B1633 is output
DTC B1638 is output
DTCs B1633 and B1638 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the connector is properly connected to the side airbag pressure sensor RH.
| Proceed to |
|---|
| The connector is properly connected |
| The connector is not properly connected |
The connector is properly connected
The connector is not properly connected
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
Disconnect the connectors from the side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.
Check that the connector (on the side airbag pressure sensor RH side) is not damaged.
| Proceed to |
|---|
| The connector is not deformed or damaged |
| The connector is deformed or damaged |
The connector is not deformed or damaged
The connector is deformed or damaged
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Pressure Sensor RH) |
| *b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I10-2 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| I10-1 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I10-2 (BDR+) - I10-1 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I10-2 (BDR+) - I10-1 (BDR-) | Always | 1 MΩ or higher |
| I10-2 (BDR+) - Body ground | Always | 1 MΩ or higher |
| I10-1 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
Connect the connectors to the side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1633 is output |
| DTC B1633 is not output |
Codes other than DTC B1633 may be output at this time, but they are not related to this check.
DTC B1633 is output
DTC B1633 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
Disconnect the floor wire connector from the front door wire RH.
Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.
| Proceed to |
|---|
| The connector is not deformed or damaged |
| The connector is deformed or damaged |
The connector is not deformed or damaged
The connector is deformed or damaged
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
| *b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IM2-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| IM2-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM2-1 (BDR+) - IM2-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM2-1 (BDR+) - IM2-2 (BDR-) | Always | 1 MΩ or higher |
| IM2-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM2-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG