Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/o Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0378287 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1651  Manual Cut OFF Switch Trouble  


DESCRIPTION

HINT:

"Manual cut off switch" refers to the airbag cutoff switch cylinder sub-assembly.


The airbag cutoff switch cylinder sub-assembly consists of the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.

The instrument panel passenger without door airbag assembly can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder sub-assembly to the "OFF" position.

If the instrument panel passenger without door airbag assembly is deactivated, the airbag cutoff switch cylinder sub-assembly comes on to inform the passengers.

DTC B1651 is stored when a malfunction is detected in the airbag cutoff switch cylinder sub-assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1651 Manual Cut OFF Switch Trouble One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff switch cylinder sub-assembly circuit for 2 seconds.

·

An airbag cutoff switch cylinder sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Airbag cutoff switch cylinder sub-assembly

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C262371E19
2.094,1.063 2.573,1.26 0.479,0.198 10 false PMC+ 2.125,2.24 2.604,2.438 0.479,0.198 10 false PMC- 5.594,3.063 5.938,3.26 0.344,0.198 10 false G70 0.344,3.198 3.167,3.406 2.823,0.208 10 false Airbag Cutoff Switch Cylinder Sub-assembly 2.573,1.073 2.813,1.281 0.24,0.208 10 false 2 2.573,2.24 2.813,2.448 0.24,0.208 10 false 1 5.51,1.063 5.76,1.271 0.25,0.208 10 false 22 5.542,2.24 5.802,2.448 0.26,0.208 10 false 21 5.771,1.146 6.302,1.344 0.531,0.198 10 false MSW+ 5.771,2.344 6.302,2.542 0.531,0.198 10 false MSW- 0.344,3.042 0.708,3.229 0.365,0.188 10 false G58 5.563,3.219 7.156,3.469 1.594,0.25 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C215710C06
0.625,1.427 0.938,1.583 0.313,0.156 10 *1 2.531,1.563 2.844,1.719 0.313,0.156 10 *2 1.49,1.104 1.802,1.26 0.313,0.156 10 *3
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Disconnect the connectors from the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.


b.

Check that the connectors (on the airbag sensor assembly side and airbag cutoff switch cylinder sub-assembly side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK INSTRUMENT PANEL WIRE

The connectors are deformed or damaged

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE
a.
C412276C01
2.583,3.5 3.031,3.75 0.448,0.25 0.531,0.583 0.979,0.833 0.448,0.25 0.969,3.698 1.167,3.698 1.167,3.698 1.594,3.979 true 1.073,3.375 1.271,3.375 1.271,3.375 1.677,3.969 true 0.917,1.375 1.115,1.375 1.115,1.375 1.385,1.156 true 1.688,1.156 1.979,1.323 1.979,1.323 2.188,1.323 true 2.021,4.344 2.115,4.469 2.115,4.469 2.323,4.469 true 0.438,2.594 0.75,2.75 0.313,0.156 10 false *1 2.813,2.698 3.125,2.854 0.313,0.156 10 false *2 1.51,1.927 1.823,2.083 0.313,0.156 10 false *3 2.365,4.375 2.677,4.531 0.313,0.156 10 false *4 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.531,3.125 0.844,3.281 0.313,0.156 10 false *b 0.594,3.292 1.104,3.573 0.51,0.281 10 false MSW+ 0.552,3.604 1.063,3.885 0.51,0.281 10 false MSW- 2.698,3.531 3.208,3.813 0.51,0.281 10 false G70 2.26,1.198 2.771,1.479 0.51,0.281 10 false PMC+ 0.5,1.25 1.01,1.531 0.51,0.281 10 false PMC- 0.625,0.615 1.135,0.896 0.51,0.281 10 false G58 0.698,2.104 0.896,2.313 0.198,0.208 10 false D 1.01,2.104 1.208,2.313 0.198,0.208 10 false C 2.385,2.115 2.583,2.323 0.198,0.208 10 false A 2.063,2.115 2.26,2.323 0.198,0.208 10 false B
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder Sub-assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G58-2 (PMC+) - Body ground Ignition switch ON Below 1 V
G58-1 (PMC-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (PMC+) - G58-1 (PMC-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (PMC+) - G58-1 (PMC-) Always 1 MΩ or higher
G58-2 (PMC+) - Body ground Always 1 MΩ or higher
G58-1 (PMC-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

4.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY
a.

Remove the airbag cutoff switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL


b.

Inspect the airbag cutoff switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

5.CHECK DTC
a.
C391328C06
1.01,1.26 1.323,1.458 0.313,0.198 10 false *1 1.823,1.375 2.135,1.573 0.313,0.198 10 false *2
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1651 is not output
DTC B1651 is output


HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.




DTC B1651 is not output

DTC B1651 is output