The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.
The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger without door airbag assembly.
DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1660 | P Seat Airbag Active Mode Indicator | One of the following conditions is met:
·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit. ·
A passenger airbag ON/OFF indicator malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Telltale light assembly (passenger airbag ON/OFF indicator) ·
Airbag sensor assembly |
Comes on | Not applicable |
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.
Refer to the normal condition of the passenger airbag ON/OFF indicator.
| Result | Proceed to |
|---|---|
| Passenger airbag ON/OFF indicator illumination is always on. | A |
| Passenger airbag ON/OFF indicator illumination is always off. | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
Disconnect the connectors from the airbag sensor assembly and telltale light assembly.
Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
Connect the connector to the telltale light assembly.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.
| Proceed to |
|---|
| The passenger airbag ON/OFF indicator does not come on |
| The passenger airbag ON/OFF indicator comes on |
The passenger airbag ON/OFF indicator does not come on
The passenger airbag ON/OFF indicator comes on
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Connect the connectors to the airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1660 is not output |
| DTC B1660 is output |
Codes other than DTC B1660 may be output at this time, but they are not related to this check.
DTC B1660 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B1660 is output
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Telltale Light Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the telltale light assembly.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
| G31-4 (PAON) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 34 (P-AB) and 35 (PAON) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - G31-4 (PAON) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - G31-4 (PAON) | Always | 1 MΩ or higher |
| G31-5 (P-AB) - Body ground | Always | 1 MΩ or higher |
| G31-4 (PAON) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
Disconnect the connectors from the airbag sensor assembly and telltale light assembly.
Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Telltale Light Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
| G31-4 (PAON) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 34 (P-AB) and 35 (PAON) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - G31-4 (PAON) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-5 (P-AB) - G31-4 (PAON) | Always | 1 MΩ or higher |
| G31-5 (P-AB) - Body ground | Always | 1 MΩ or higher |
| G31-4 (PAON) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Telltale Light Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G31-9 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Connect the connector to the telltale light assembly.
Using a service wire, connect terminal 35 (PAON) and body ground.
Using a service wire, connect terminal 34 (P-AB) and body ground.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the indicator according to the table below.
| Tester Connection | Switch Condition | Passenger Airbag ON/OFF Indicator |
|---|---|---|
| G70-35 (PAON) - Body ground | Ignition switch ON | "ON" comes on |
| G70-34 (P-AB) - Body ground | Ignition switch ON | "OFF" comes on |
Turn the ignition switch off.
Disconnect the service wire from airbag sensor assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Connect the connectors to the airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1660 is not output |
| DTC B1660 is output |
Codes other than DTC B1660 may be output at this time, but they are not related to this check.
DTC B1660 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B1660 is output