Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM (for Gasoline Model)
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0376805 POWER BACK DOOR SYSTEM(for Gasoline Model) Y

DOOR / HATCH  POWER BACK DOOR SYSTEM(for Gasoline Model)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

The power back door system troubleshooting procedure is based on the premise that the entry and start system (for Entry Function, Gasoline Model) is operating normally. Check the power back door system first before troubleshooting the power back door system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Use the following procedure to troubleshoot the power back door system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

A simple method to determine whether the battery is discharged is to operate the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

3.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
3.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTC is not output A
LIN DTC is output B



A

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

b.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

c.

Recheck for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
a.

Check whether the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has been performed.


Result:
Result Proceed to
The replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has been performed. A
The replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has not been performed. B



A

9.INITIALIZE POWER BACK DOOR SYSTEM

B

10.CONFIRMATION TEST
9.INITIALIZE POWER BACK DOOR SYSTEM

Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END